AD9233-125EBZ Analog Devices Inc, AD9233-125EBZ Datasheet - Page 17

1.8V 12Bit 125 Msps ADC EB

AD9233-125EBZ

Manufacturer Part Number
AD9233-125EBZ
Description
1.8V 12Bit 125 Msps ADC EB
Manufacturer
Analog Devices Inc
Datasheet

Specifications of AD9233-125EBZ

Number Of Adc's
1
Number Of Bits
12
Sampling Rate (per Second)
125M
Data Interface
Serial
Inputs Per Adc
1 Differential
Input Range
1 ~ 2 Vpp
Power (typ) @ Conditions
455mW @125MSPS
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD9233
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Single-Ended Input Configuration
Although not recommended, it is possible to operate the
AD9233 in a single-ended input configuration, as long as the
input voltage swing is within the AVDD supply. Single-ended
operation can provide adequate performance in cost-sensitive
applications. In this configuration, SFDR and distortion
performance degrade due to the large input common-mode
swing. If the source impedances on each input are matched,
there should be little effect on SNR performance. Figure 41
details a typical single-ended input configuration.
VOLTAGE REFERENCE
A stable and accurate voltage reference is built into the AD9233.
The input range is adjustable by varying the reference voltage
applied to the AD9233, using either the internal reference or an
externally applied reference voltage. The input span of the ADC
tracks reference voltage changes linearly. The various reference
modes are summarized in the following sections. The Reference
Decoupling section describes the best practices and requirements
for PCB layout of the reference.
Internal Reference Connection
A comparator within the AD9233 detects the potential at the
SENSE pin and configures the reference into four possible
states, which are summarized in Table 9. If SENSE is grounded,
the reference amplifier switch is connected to the internal
resistor divider (see Figure 42), setting VREF to 1 V.
Connecting the SENSE pin to VREF switches the reference
amplifier output to the SENSE pin, completing the loop and
providing a 0.5 V reference output. If a resistor divider is
connected external to the chip, as shown in Figure 43, the
switch again sets to the SENSE pin.
1V p-p
10µF
49.9Ω
Figure 41. Single-Ended Input Configuration
0.1µF
10µF
0.1µF
AVDD
1kΩ
1kΩ
1kΩ
1kΩ
AVDD
R
R
C
VIN+
VIN–
AD9233
ADC
Rev. A | Page 17 of 44
This puts the reference amplifier in a noninverting mode with
the VREF output defined as
If the SENSE pin is connected to the AVDD pin, the reference
amplifier is disabled, and an external reference voltage can be
applied to the VREF pin (see the External Reference Operation
section).
The input range of the ADC always equals twice the voltage at
the reference pin for either an internal or an external reference.
If the internal reference of the AD9233 is used to drive multiple
converters to improve gain matching, the loading of the
reference by the other converters must be considered. Figure 44
depicts how the internal reference voltage is affected by loading.
0.1µF
VREF
0.1µF
Figure 43. Programmable Reference Configuration
=
0.1µF
0
Figure 42. Internal Reference Configuration
5 .
VREF
0.1µF
×
SENSE
VREF
⎛ +
VIN+
VIN–
1
SENSE
R2
R1
VIN+
VIN–
R
R
2
1
SELECT
LOGIC
SELECT
LOGIC
CORE
ADC
AD9233
CORE
0.5V
ADC
AD9233
0.5V
REFT
REFB
AD9233
0.1µF
REFT
REFB
0.1µF

Related parts for AD9233-125EBZ