ATTINY2313-20PJ Atmel, ATTINY2313-20PJ Datasheet - Page 116

• Manufacturer Part Number: ATTINY2313-20PJ
• Description: IC MCU AVR 2K FLASH 20DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313-20PJ

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Other names: ATTINY2313-24PJ; ATTINY2313-24PJ

USART
Initialization
116
ATtiny2313
If used, the parity bit is located between the last data bit and first stop bit of a serial frame.
The USART has to be initialized before any communication can take place. The initialization pro-
cess normally consists of setting the baud rate, setting frame format and enabling the
Transmitter or the Receiver depending on the usage. For interrupt driven USART operation, the
Global Interrupt Flag should be cleared (and interrupts globally disabled) when doing the
initialization.
Before doing a re-initialization with changed baud rate or frame format, be sure that there are no
ongoing transmissions during the period the registers are changed. The TXC flag can be used to
check that the Transmitter has completed all transfers, and the RXC flag can be used to check
that there are no unread data in the receive buffer. Note that the TXC flag must be cleared
before each transmission (before UDR is written) if it is used for this purpose.
The following simple USART initialization code examples show one assembly and one C func-
tion that are equal in functionality. The examples assume asynchronous operation using polling
(no interrupts enabled) and a fixed frame format. The baud rate is given as a function parameter.
For the assembly code, the baud rate parameter is assumed to be stored in the r17:r16
Registers.
Note:
Assembly Code Example
C Code Example
d
n
USART_Init:
void USART_Init( unsigned int baud )
{
}
; Set baud rate
out
out
; Enable receiver and transmitter
ldi
out
; Set frame format: 8data, 2stop bit
ldi
out
ret
/* Set baud rate */
UBRRH = (unsigned char)(baud>>8);
UBRRL = (unsigned char)baud;
/* Enable receiver and transmitter */
UCSRB = (1<<RXEN)|(1<<TXEN);
/* Set frame format: 8data, 2stop bit */
UCSRC = (1<<USBS)|(3<<UCSZ0);
1. The example code assumes that the part specific header file is included.
Data bit n of the character
For I/O Registers located in extended I/O map, “IN”, “OUT”, “SBIS”, “SBIC”, “CBI”, and “SBI”
instructions must be replaced with instructions that allow access to extended I/O. Typically
“LDS” and “STS” combined with “SBRS”, “SBRC”, “SBR”, and “CBR”.
UBRRH, r17
UBRRL, r16
r16, (1<<RXEN)|(1<<TXEN)
UCSRB,r16
r16, (1<<USBS)|(3<<UCSZ0)
UCSRC,r16
(1)
(1)
2543L–AVR–08/10