ST7FLITES2Y0M6 STMicroelectronics, ST7FLITES2Y0M6 Datasheet - Page 43

• Manufacturer Part Number: ST7FLITES2Y0M6
• Description: MCU 8BIT 1K FLASH 16SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITES2Y0M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 1KB (1K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SOIC (3.9mm Width)
• Controller Family/series: ST7
• No. Of I/o's: 13
• Ram Memory Size: 128Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SPI
• No. Of Pwm Channels: 1
• Rohs Compliant: Yes
• Processor Series: ST7FLITESx
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLIT0-IND/USB, ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: In Transition
• Other names: 497-4861

Output Modes
The output configuration is selected by setting the
corresponding DDR register bit. In this case, writ-
ing the DR register applies this digital value to the
I/O pin through the latch. Then reading the DR reg-
ister returns the previously stored value.
Two different output modes can be selected by
software through the OR register: Output push-pull
and open-drain.
DR register value and output pin status:
Note: When switching from input to output mode,
the DR register has to be written first to drive the
correct level on the pin as soon as the port is con-
figured as an output.
– reset the interrupt mask with the RIM instruc-
DR
tion (in cases where a pin level change could
occur)
0
1
Push-pull
V
V
DD
SS
Open-drain
Floating
Vss
10.2.2 Alternate Functions
When an on-chip peripheral is configured to use a
pin, the alternate function is automatically select-
ed. This alternate function takes priority over the
standard I/O programming under the following
conditions:
– When the signal is coming from an on-chip pe-
– When the signal is going to an on-chip peripher-
Notes:
– Input pull-up configuration can cause unexpect-
– When an on-chip peripheral use a pin as input
ripheral, the I/O pin is automatically configured in
output mode (push-pull or open drain according
to the peripheral).
al, the I/O pin must be configured in floating input
mode. In this case, the pin state is also digitally
readable by addressing the DR register.
ed value at the input of the alternate peripheral
input.
and output, this pin has to be configured in input
floating mode.
ST7LITE0xY0, ST7LITESxY0
43/124
1