PIC18F45K20-I/ML Microchip Technology, PIC18F45K20-I/ML Datasheet - Page 59

• Manufacturer Part Number: PIC18F45K20-I/ML
• Description: IC PIC MCU FLASH 16KX16 44QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F45K20-I/ML

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 44-QFN
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 35
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: CCP/ECCP/EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14-ch x 10-bit
• Package: 44QFN EP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 64 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM240313 - BOARD DEMO 8BIT XLPAC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPDM164124 - KIT STARTER FOR PIC18F4XK20AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FIGURE 3-46:
© 2009 Microchip Technology Inc.
3.9.2
The internal oscillator block is selected as the primary oscillator in the Configuration
bits. The OSC bits in the CONFIG1H Configuration Word are set to either INTIO67 or
INTIO7. When INTIO67 is selected, the internal oscillator is the primary oscillator with
the external oscillator pins OSC2 and OSC1 available as RA6 and RA7 IO. OSC =
INTIO7 differs only in that RA6 is not available; instead the internal instruction clock is
output as CLKO on that pin.
The two Special Function Registers that control the internal oscillator block in software
are OSCCON and OSCTUNE, shown in figures 3-44 and 3-45.
OSCCON: OSCILLATOR CONTROL REGISTER
The IDLEN bit in OSCCON affects how the oscillator behaves in power managed
modes, and is not discussed further here.
The IRFCx bits determine the internal oscillator frequency. These are the outputs of the
postscaler. As Note 2 in Figure 3-44 indicates, the 31 kHz clock can be selected as
either a postscaled version of the INTOSC 8 MHz oscillator, on which all other
frequencies are based, or the INTRC low-power 31 kHz oscillator as discussed in
Section 3.9.1. This selection is made with the INTSRC bit in the OSCTUNE register.
Configuring the Internal Oscillator
PICkit™ 3 Debug Express Lessons
DS41370C-page 55