C8051F321-GM Silicon Laboratories Inc, C8051F321-GM Datasheet - Page 89

• Manufacturer Part Number: C8051F321-GM
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F321-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit or 17-ch x 10-bit
• No. Of I/o's: 21
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1480 - DAUGHTER CARD TOOLSTCK C8051F321770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1449 - ADAPTER PROGRAM TOOLSTICK F321336-1260 - DEV KIT FOR C8051F320/F321
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1261

9.3.4. Interrupt Latency
Interrupt response time depends on the state of the CPU when the interrupt occurs. Pending interrupts are
sampled and priority decoded each system clock cycle. Therefore, the fastest possible response time is 5
system clock cycles: 1 clock cycle to detect the interrupt and 4 clock cycles to complete the LCALL to the
ISR. If an interrupt is pending when a RETI is executed, a single instruction is executed before an LCALL
is made to service the pending interrupt. Therefore, the maximum response time for an interrupt (when no
other interrupt is currently being serviced or the new interrupt is of greater priority) occurs when the CPU is
performing an RETI instruction followed by a DIV as the next instruction. In this case, the response time is
18 system clock cycles: 1 clock cycle to detect the interrupt, 5 clock cycles to execute the RETI, 8 clock
cycles to complete the DIV instruction and 4 clock cycles to execute the LCALL to the ISR. If the CPU is
executing an ISR for an interrupt with equal or higher priority, the new interrupt will not be serviced until the
current ISR completes, including the RETI and following instruction.
Note that the CPU is stalled during Flash write/erase operations and USB FIFO MOVX accesses (see Sec-
tion “12.2. Accessing USB FIFO Space” on page 114). Interrupt service latency will be increased for inter-
rupts occuring while the CPU is stalled. The latency for these situations will be determined by the standard
interrupt service procedure (as described above) and the amount of time the CPU is stalled.
Interrupt Source
Reset
External Interrupt 0
(/INT0)
Timer 0 Overflow
External Interrupt 1
(/INT1)
Timer 1 Overflow
UART0
Timer 2 Overflow
SPI0
SMB0
USB0
ADC0 Window
Compare
Interrupt
0x000B
0x001B
0x002B
0x003B
0x004B
0x0000
0x0003
0x0013
0x0023
0x0033
0x0043
Vector
Table 9.4. Interrupt Summary
Priority
Order
Top
0
1
2
3
4
5
6
7
8
9
Pending Flag
None
IE0 (TCON.1)
TF0 (TCON.5)
IE1 (TCON.3)
TF1 (TCON.7)
RI0 (SCON0.0)
TI0 (SCON0.1)
TF2H (TMR2CN.7)
TF2L (TMR2CN.6)
SPIF (SPI0CN.7)
WCOL (SPI0CN.6)
MODF (SPI0CN.5)
RXOVRN
(SPI0CN.4)
SI (SMB0CN.0)
Special
AD0WINT
(ADC0CN.3)
Rev. 1.4
N/A N/A
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
C8051F320/1
Y
Y
Y
Y
N
N
N
N
N
N
Enable
Flag
Always
Enabled
EX0 (IE.0)
ET0 (IE.1) PT0 (IP.1)
EX1 (IE.2)
ET1 (IE.3) PT1 (IP.3)
ES0 (IE.4)
ET2 (IE.5) PT2 (IP.5)
ESPI0
(IE.6)
ESMB0
(EIE1.0)
EUSB0
(EIE1.1)
EWADC0
(EIE1.2)
Priority
Control
Always
Highest
PX0
(IP.0)
PX1
(IP.2)
PS0
(IP.4)
PSPI0
(IP.6)
PSMB0
(EIP1.0)
PUSB0
(EIP1.1)
PWADC0
(EIP1.2)
89