C8051F321-GM Silicon Laboratories Inc, C8051F321-GM Datasheet - Page 164

• Manufacturer Part Number: C8051F321-GM
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F321-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit or 17-ch x 10-bit
• No. Of I/o's: 21
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1480 - DAUGHTER CARD TOOLSTCK C8051F321770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1449 - ADAPTER PROGRAM TOOLSTICK F321336-1260 - DEV KIT FOR C8051F320/F321
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1261

C8051F320/1
15.13. Controlling Endpoints1–3 OUT
Endpoints1-3 OUT are managed via USB registers EOUTCSRL and EOUTCSRH. All OUT endpoints can
be used for Interrupt, Bulk, or Isochronous transfers. Isochronous (ISO) mode is enabled by writing ‘1’ to
the ISO bit in register EOUTCSRH. Bulk and Interrupt transfers are handled identically by hardware.
An Endpoint1-3 OUT interrupt may be generated by the following:
15.13.1.Endpoints1-3 OUT Interrupt or Bulk Mode
When the ISO bit (EOUTCSRH.6) = ‘0’ the target endpoint operates in Bulk or Interrupt mode. Once an
endpoint has been configured to operate in Bulk/Interrupt OUT mode (typically following an Endpoint0
SET_INTERFACE command), hardware will set the OPRDY bit (EOUTCSRL.0) to ‘1’ and generate an
interrupt upon reception of an OUT token and data packet. The number of bytes in the current OUT data
packet (the packet ready to be unloaded from the FIFO) is given in the EOUTCNTH and EOUTCNTL reg-
isters. In response to this interrupt, firmware should unload the data packet from the OUT FIFO and reset
the OPRDY bit to ‘0’.
164
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bits1–0: Unused. Read = 00b; Write = don’t care.
USB Register Definition 15.20. EINCSRH: USB0 IN Endpoint Control High Byte
DBIEN
R/W
Bit7
1. Hardware sets the OPRDY bit (EINCSRL.0) to ‘1’.
2. Hardware generates a STALL condition.
DBIEN: IN Endpoint Double-buffer Enable.
0: Double-buffering disabled for the selected IN endpoint.
1: Double-buffering enabled for the selected IN endpoint.
ISO: Isochronous Transfer Enable.
This bit enables/disables isochronous transfers on the current endpoint.
0: Endpoint configured for bulk/interrupt transfers.
1: Endpoint configured for isochronous transfers.
DIRSEL: Endpoint Direction Select.
This bit is valid only when the selected FIFO is not split (SPLIT = ‘0’).
0: Endpoint direction selected as OUT.
1: Endpoint direction selected as IN.
Unused. Read = ‘0b’. Write = don’t care.
FCDT: Force Data Toggle.
0: Endpoint data toggle switches only when an ACK is received following a data packet
transmission.
1: Endpoint data toggle forced to switch after every data packet is transmitted, regardless of
ACK reception.
SPLIT: FIFO Split Enable.
When SPLIT = ‘1’, the selected endpoint FIFO is split. The upper half of the selected FIFO is
used by the IN endpoint; the lower half of the selected FIFO is used by the OUT endpoint.
ISO
R/W
Bit6
DIRSEL
R/W
Bit5
Bit4
R
-
Rev. 1.4
FCDT
R/W
Bit3
SPLIT
R/W
Bit2
Bit1
R
-
Bit0
R
-
USB Address:
00000000
Reset Value
0x12