C8051F330-GM Silicon Laboratories Inc, C8051F330-GM Datasheet - Page 207

• Manufacturer Part Number: C8051F330-GM
• Description: IC 8051 MCU 8K FLASH 20MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F33xr

Specifications of C8051F330-GM

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 20-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F330DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• No. Of I/o's: 17
• Ram Memory Size: 768Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1541 - KIT TOOL EVAL SYS IN A USB STICK770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1451 - ADAPTER PROGRAM TOOLSTICK F330336-1346 - DAUGHTER CARD TOOLSTICK F330336-1264 - DEV KIT FOR C8051F330/F331
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1262

20.2. C2 Pin Sharing
The C2 protocol allows the C2 pins to be shared with user functions so that in-system debugging and
Flash programming may be performed. This is possible because C2 communication is typically performed
when the device is in the halt state, where all on-chip peripherals and user software are stalled. In this
halted state, the C2 interface can safely ‘borrow’ the C2CK (RST) and C2D (P2.0) pins. In most applica-
tions, external resistors are required to isolate C2 interface traffic from the user application. A typical isola-
tion configuration is shown in Figure 20.1.
The configuration in Figure 20.1 assumes the following:
Additional resistors may be necessary depending on the specific application.
1. The user input (b) cannot change state while the target device is halted.
2. The RST pin on the target device is used as an input only.
/Reset (a)
Output (c)
Input (b)
Figure 20.1. Typical C2 Pin Sharing
C2 Interface Master
Rev. 1.7
C8051F330/1/2/3/4/5
C2CK
C2D
C8051Fxxx
211