C8051F332-GM Silicon Laboratories Inc, C8051F332-GM Datasheet - Page 206

• Manufacturer Part Number: C8051F332-GM
• Description: IC 8051 MCU 4KB FLASH 20QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F33xr

Specifications of C8051F332-GM

• Program Memory Type: FLASH
• Program Memory Size: 4KB (4K x 8)
• Package / Case: 20-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F330DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• No. Of I/o's: 17
• Ram Memory Size: 768Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Package: 20QFN
• Device Core: 8051
• Family Name: C8051F33x
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1451 - ADAPTER PROGRAM TOOLSTICK F330
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1266

C8051F330/1/2/3/4/5
210
This read-only register returns the 8-bit revision ID: 0x00 (Revision A).
Bits7 – 0
Bits7 – 0: FPDAT: C2 Flash Programming Data Register.
Bit7
Bit7
Bit7
C2 Register Definition 20.4. FPCTL: C2 Flash Programming Control
C2 Register Definition 20.5. FPDAT: C2 Flash Programming Data
FPCTL: Flash Programming Control Register.
This register is used to enable Flash programming via the C2 interface. To enable C2 Flash
programming, the following codes must be written in order: 0x02, 0x01. Note that once C2
Flash programming is enabled, a system reset must be issued to resume normal operation.
This register is used to pass Flash commands, addresses, and data during C2 Flash
accesses. Valid commands are listed below.
Code
0x06
0x07
0x08
0x03
Bit6
Bit6
Bit6
C2 Register Definition 20.3. REVID: C2 Revision ID
Bit5
Bit5
Bit5
Flash Page Erase
Flash Block Read
Flash Block Write
Device Erase
Command
Bit4
Bit4
Bit4
Rev. 1.7
Bit3
Bit3
Bit3
Bit2
Bit2
Bit2
Bit1
Bit1
Bit1
Bit0
Bit0
Bit0
00000000
00000000
00000000
Reset Value
Reset Value
Reset Value