PIC18F4525-I/ML Microchip Technology, PIC18F4525-I/ML Datasheet - Page 186

• Manufacturer Part Number: PIC18F4525-I/ML
• Description: IC MCU FLASH 24KX16 44QFN
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4525-I/ML

• Core Size: 8-Bit
• Program Memory Size: 48KB (24K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3968Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3986 B
• Interface Type: SPI, I2C, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, 53275-917, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13 bit
• Package: 44QFN EP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44QFN2 - SOCKET TRAN ICE 44QFN/40DIPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNI3DB18F4620 - BOARD DAUGHTER ICEPIC3444-1001 - DEMO BOARD FOR PICMICRO MCU
• Lead Free Status / Rohs Status: Details

PIC18F2525/2620/4525/4620
17.4.5
The addressing procedure for the I
the first byte after the Start condition usually
determines which device will be the slave addressed by
the master. The exception is the general call address
which can address all devices. When this address is
used, all devices should, in theory, respond with an
Acknowledge.
The general call address is one of eight addresses
reserved for specific purposes by the I
consists of all ‘0’s with R/W = 0.
The general call address is recognized when the
General
(SSPCON2<7> is set). Following a Start bit detect,
8 bits are shifted into the SSPSR and the address is
compared against the SSPADD. It is also compared to
the general call address and fixed in hardware.
FIGURE 17-15:
DS39626E-page 184
GCEN (SSPCON2<7>)
SSPOV (SSPCON1<6>)
SDA
SCL
SSPIF
BF (SSPSTAT<0>)
Call
GENERAL CALL ADDRESS
SUPPORT
Enable
S
SLAVE MODE GENERAL CALL ADDRESS SEQUENCE
(7 OR 10-BIT ADDRESSING MODE)
bit,
1
2
GCEN,
General Call Address
2
C bus is such that
3
2
4
C protocol. It
is
5
enabled
6
7
R/W =
8
0
If the general call address matches, the SSPSR is
transferred to the SSPBUF, the BF flag bit is set (eighth
bit) and on the falling edge of the ninth bit (ACK bit), the
SSPIF interrupt flag bit is set.
When the interrupt is serviced, the source for the
interrupt can be checked by reading the contents of the
SSPBUF. The value can be used to determine if the
address was device specific or a general call address.
In 10-bit mode, the SSPADD is required to be updated
for the second half of the address to match and the UA
bit (SSPSTAT<1>) is set. If the general call address is
sampled when the GCEN bit is set, while the slave is
configured in 10-Bit Addressing mode, then the second
half of the address is not necessary, the UA bit will not
be set and the slave will begin receiving data after the
Acknowledge (Figure 17-15).
ACK
Address is compared to General Call Address
after ACK, set interrupt
9
D7
1
D6
2
Cleared in software
SSPBUF is read
Receiving Data
D5
3
D4
4
© 2008 Microchip Technology Inc.
D3
5
D2
6
D1
7
D0
8
ACK
9
‘0’
‘1’