ATMEGA32A-AU Atmel, ATMEGA32A-AU Datasheet - Page 32

• Manufacturer Part Number: ATMEGA32A-AU
• Description: MCU AVR 32K FLASH 16MHZ 44-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32A-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire/SPI/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Data Rom Size: 1024 B
• Height: 1 mm
• Length: 10 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 10 mm
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK524 - KIT STARTER ATMEGA32M1/MEGA32C1ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.10
8.10.1
8155C–AVR–02/11
Register Description
OSCCAL – Oscillator Calibration Register
• Bits 7:0 – CAL7:0: Oscillator Calibration Value
Writing the calibration byte to this address will trim the Internal Oscillator to remove process vari-
ations from the Oscillator frequency. During Reset, the 1MHz calibration value which is located
in the signature row High Byte (address 0x00) is automatically loaded into the OSCCAL Regis-
ter. If the internal RC is used at other frequencies, the calibration values must be loaded
manually. This can be done by first reading the signature row by a programmer, and then store
the calibration values in the Flash or EEPROM. Then the value can be read by software and
loaded into the OSCCAL Register. When OSCCAL is zero, the lowest available frequency is
chosen. Writing non-zero values to this register will increase the frequency of the Internal Oscil-
lator. Writing $FF to the register gives the highest available frequency. The calibrated Oscillator
is used to time EEPROM and Flash access. If EEPROM or Flash is written, do not calibrate to
more than 10% above the nominal frequency. Otherwise, the EEPROM or Flash write may fail.
Note that the Oscillator is intended for calibration to 1.0, 2.0z, 4.0, or 8.0MHz. Tuning to other
values is not guaranteed, as indicated in
Table 8-11.
Bit
Read/Write
Initial Value
OSCCAL Value
$FF
$00
$7F
Internal RC Oscillator Frequency Range.
CAL7
R/W
7
Min Frequency in Percentage of
CAL6
R/W
6
Nominal Frequency (%)
CAL5
R/W
5
100
50
75
Device Specific Calibration Value
Table
CAL4
R/W
4
8-11.
CAL3
R/W
3
CAL2
Max Frequency in Percentage of
R/W
2
Nominal Frequency (%)
CAL1
R/W
1
ATmega32A
100
150
200
CAL0
R/W
0
OSCCAL
32