PIC24HJ16GP304-I/ML Microchip Technology, PIC24HJ16GP304-I/ML Datasheet - Page 157

• Manufacturer Part Number: PIC24HJ16GP304-I/ML
• Description: IC PIC MCU FLASH 16K 44QFN
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ16GP304-I/ML

• Program Memory Type: FLASH
• Program Memory Size: 16KB (5.5K x 24)
• Package / Case: 44-QFN
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 13x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

18.0
The PIC24HJ32GP202/204 and PIC24HJ16GP304
devices have up to 13 Analog-to-Digital Conversion
(ADC) module input channels.
The AD12B bit (AD1CON1<10>) allows each of the
ADC modules to be configured as either a 10-bit,
4-sample-and-hold ADC (default configuration), or a
12-bit, 1- sample and hold ADC.
18.1
The 10-bit ADC configuration has the following key
features:
• Successive Approximation (SAR) conversion
• Conversion speeds of up to 1.1 Msps
• Up to 13 analog input pins
• External voltage reference input pins
• Simultaneous sampling of up to four analog input
• Automatic Channel Scan mode
• Selectable conversion trigger source
• Selectable Buffer Fill modes
• Operation during CPU Sleep and Idle modes
• 16-word conversion result buffer
© 2011 Microchip Technology Inc.
Note:
pins
Note 1: This data sheet summarizes the features
2: Some registers and associated bits
10-BIT/12-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC)
Key Features
PIC24HJ32GP202/204 AND PIC24HJ16GP304
The ADC module must be disabled before
the AD12B bit can be modified.
of
PIC24HJ16GP304 family of devices.
However, it is not intended to be a com-
prehensive reference source. To comple-
ment the information in this data sheet,
refer to “Section 16. Analog-to-Digital
Converter (ADC) with DMA” (DS70210)
of the “dsPIC33F/PIC24H Family Refer-
ence Manual”, which is available from the
Microchip website (www.microchip.com).
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization”
this data sheet for device-specific register
and bit information.
the
PIC24HJ32GP202/204
and
in
The 12-bit ADC configuration supports all the above
features, except:
• In the 12-bit configuration, conversion speeds of
• There is only 1 sample-and-hold amplifier in the
Depending on the particular device pinout, the ADC
can have up to 13 analog input pins, designated AN0
through AN12. In addition, there are two analog input
pins for external voltage reference connections. These
voltage reference inputs can be shared with other
analog input pins.
The actual number of analog input pins and external
voltage reference input configuration will depend on the
specific device. Refer to the device data sheet for
further details.
A block diagram of ADC for PIC24HJ16GP304 and
PIC24HJ32GP204 devices is shown in
block diagram of the ADC for the PIC24HJ32GP202
device is shown in
18.2
To configure the ADC module:
1.
2.
3.
4.
5.
6.
7.
8.
up to 500 ksps are supported
12-bit configuration, so simultaneous sampling of
multiple channels is not supported
Select
(AD1PCFGH<15:0> or AD1PCFGL<15:0>).
Select voltage reference source to match
expected
(AD1CON2<15:13>).
Select the analog conversion clock to match
desired
(AD1CON3<7:0>).
Determine
channels will be used (AD1CON2<9:8> and
AD1PCFGH<15:0> or AD1PCFGL<15:0>).
Select
sequence
AD1CON3<12:8>).
Select the way conversion results are presented
in the buffer (AD1CON1<9:8>).
Turn on the ADC module (AD1CON1<15>).
Configure ADC interrupt (if required):
a)
b)
ADC Initialization
Clear the AD1IF bit.
Select ADC interrupt priority.
the
port
data
range
how
Figure
appropriate
rate
pins
(AD1CON1<7:5>
18-2.
many
with
on
as
sample/conversion
processor
analog
DS70289G-page 157
sample-and-hold
analog
Figure
inputs
inputs
clock
18-1. A
and