PIC16C770-I/SO Microchip Technology, PIC16C770-I/SO Datasheet - Page 111

• Manufacturer Part Number: PIC16C770-I/SO
• Description: IC MCU OTP 2KX14 A/D PWM 20-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C770-I/SO

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI
• Number Of I /o: 15
• Program Memory Type: OTP
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 6x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Controller Family/series: PIC16C
• No. Of I/o's: 16
• Ram Memory Size: 256Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMINGAC164028 - MODULE SKT PROMATEII 20SOIC/DIP309-1013 - ADAPTER 20-SOIC TO 20-DIP309-1012 - ADAPTER 20-SOIC TO 20-DIP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: PIC16C770I/SO

After the A/D module has been configured as desired
and the analog input channels have their correspond-
ing TRIS bits selected for port inputs, the selected
channel must be acquired before conversion is
started. The A/D conversion cycle can be initiated by
setting the GO/DONE bit. The A/D conversion begins
and lasts for 13T
lowed for performing an A/D conversion:
1.
2.
3.
FIGURE 11-3:
2002 Microchip Technology Inc.
Configure port pins:
• Configure Analog Input mode (ANSEL)
• Configure pin as input (TRISA or TRISB)
Configure the A/D module
• Configure A/D Result Format / voltage refer-
• Select A/D input channel (ADCON0)
• Select A/D conversion clock (ADCON0)
• Turn on A/D module (ADCON0)
Configure A/D interrupt (if required)
• Clear ADIF bit
• Set ADIE bit
• Set PEIE bit
• Set GIE bit
C
ence (ADCON1)
ONVERTER
A/D
AD
. The following steps should be fol-
(R
(R
VOLTAGE
A/D BLOCK DIAGRAM
VOLTAGE
EFERENCE
EFERENCE
V
V
REF
REF
-
+
(I
-)
+)
NPUT VOLTAGE
VCFG<2:0>
VCFG<2:0>
V
AIN
)
AV
AV
DD
SS
VRH
VRL
VRL
4.
5.
6.
7.
8.
Clearing the GO/DONE bit during a conversion will
abort the current conversion. The ADRESH and
ADRESL registers will be updated with the partially
completed A/D conversion value. That is, the
ADRESH and ADRESL registers will contain the value
of the current incomplete conversion.
Note:
PIC16C717/770/771
Wait the required acquisition time.
START conversion
• Set GO/DONE bit (ADCON0)
Wait 13T
either:
• Polling for the GO/DONE bit to be cleared
OR
• Waiting for the A/D interrupt
Read A/D Result registers (ADRESH and
ADRESL), clear ADIF if required.
For next conversion, go to step 1, step 2 or step
3 as required.
Do not set the ADON bit and the GO/
DONE bit in the same instruction. Doing so
will cause the GO/DONE bit to be automat-
ically cleared.
CHS<3:0>
AD
until A/D conversion is complete, by
RA1/AN1
RA2/AN2/V
RA0/AN0
RB1/AN5/SS
RB0/AN4/INT
RA3/AN3/V
DS41120B-page 109
REF
REF
-/VRL
+/VRH