RDER72J104K8K1C11B Murata Electronics North America, RDER72J104K8K1C11B Datasheet - Page 28

• Manufacturer Part Number: RDER72J104K8K1C11B
• Description: CAP CER 100000PF 630V X7R RADIAL
• Manufacturer: Murata Electronics North America
• Series: RDEr

Specifications of RDER72J104K8K1C11B

• Capacitance: 0.1µF
• Voltage - Rated: 630V
• Tolerance: ±10%
• Temperature Coefficient: X7R
• Mounting Type: Through Hole
• Operating Temperature: -55°C ~ 125°C
• Features: High Voltage
• Applications: General Purpose
• Package / Case: Radial
• Size / Dimension: 0.217" L x 0.295" W (5.50mm x 7.50mm)
• Thickness: 4.00mm Max
• Lead Spacing: 0.197" (5.00mm)
• Lead Style: Flat Bent
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Ratings: -
• Other names: 490-4821

4
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
26
No.
11 Solderability of Leads
12
13
14
15
16
17
RDE Series (Only for Commercial) Specifications and Test Methods
Specifications and Test Methods
Continued from the preceding page.
Resistance
to
Soldering
Heat
Temperature
and
Immersion
Cycle
Humidity
(Steady
State)
Humidity
Load
High
Temperature
Load
Solvent
Resistance
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance No defects or abnormalities
Capacitance
Change
Dielectric
Strength
(Between
Terminals)
Appearance No defects or abnormalities
Capacitance
Change
D.F.
Insulation
Resistance
Dielectric
Strength
(Between
Terminals)
Appearance No defects or abnormalities
Capacitance
Change
D.F.
Insulation
Resistance
Appearance No defects or abnormalities
Capacitance
Change
D.F.
Insulation
Resistance
Appearance No defects or abnormalities
Capacitance
Change
D.F.
Insulation
Resistance
Appearance No defects or abnormalities
Marking
Lead wire should be soldered with uniform coating on the axial
direction over 3/4 of the circumferential direction.
Within T10%
No defects
Within T12.5%
0.05 max.
CF0.01 F : 1,000M min.
CU0.01 F : 10M · F min.
No defects or abnormalities
Within T15%
0.05 max.
CF0.01 F : 1,000M min.
CU0.01 F : 10M · F min.
Within T15%
0.05 max.
CF0.01 F : 1,000M min.
CU0.01 F : 10M · F min.
Within T15%
0.05 max.
CF0.01 F : 1,000M min.
CU0.01 F : 10M · F min.
Legible
Specifications
The terminal of a capacitor is dipped into a solution of
ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin
in weight proportion) and then into molten solder (JIS-
Z-3282) for 2T0.5 sec. In both cases the depth of
dipping is up to about 1.5 to 2mm from the terminal
body.
Temp. of solder: 245T5˚C Lead Free Solder (Sn-3.0Ag-0.5Cu)
The lead wire is immersed in the melted solder 1.5 to
2mm from the main body at 350T10˚C for 3.5T0.5 sec.
The specified items are measured after 24T2 hrs.
• Pretreatment
Perform a heat treatment at 150+0/-10˚C for 1 hr., and
then let sit at room temperature for 24T2 hrs.
First, repeat 5 cycles according to the 4 heat
treatments listed in the following table. Next, repeat
twice the successive cycles of immersion, each cycle
consisting of immersion in fresh water at 65+5/-0˚C for
15 min. and immersion in a saturated aqueous solution
of salt at 0T3˚C for 15 min. The capacitor is then
promptly washed in running water, dried with a drying
cloth, and allowed to sit at room temperature for 24T2
hrs.
• Pretreatment
Perform a heat treatment at 150+0/-10˚C for 1 hr., and
then let sit at room temperature for 24T2 hrs.
Set the capacitor at 40T2˚C and relative humidity of 90
to 95% for 500
at room temperature, then measure.
Apply the rated voltage at 40T2˚C and relative humidity
of 90 to 95% for 500
24T2 hrs. at room temperature, then measure.
(Charge/Discharge current V 50mA)
Apply voltage in Table for 1000
maximum operating temperature. Remove and set for
24T2 hrs. at room temperature, then measure.
(Charge/Discharge current V 50mA)
• Pretreatment
Apply test voltage for 1 hr., at test temperature. Remove
and set for 24T2 hrs. at room temperature.
The capacitor should be fully immersed, unagitated, in
reagent at 20 to 25˚C for 30T5 sec. and then remove
gently. Marking on the surface of the capacitor should
immediately be visually examined.
Reagent:
• Isopropyl alcohol
Rated Voltage
Temp.
(min.)
Step
Time
(˚C)
DC250V
DC630V
Operating
Temp. T3
30T3
Min.
235T5˚C H60A or H63A Eutectic Solder
W
Y
1
24
0
hrs. Remove and set for 24T2 hrs.
Test Method
W
Y
24
150% of the rated voltage
120% of the rated voltage
3 max.
0
Temp.
Room
hrs. Remove and set for
2
Test Voltage
W
Y
Operating
Temp. T3
48
0
30T3
Max.
hrs. at the
3
3 max.
Temp.
Room
4
C49E.pdf
10.3.8