58330-1 Tyco Electronics, 58330-1 Datasheet

DIE ASSY U/W A9996-ND

58330-1

Manufacturer Part Number
58330-1
Description
DIE ASSY U/W A9996-ND
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ IIIr
Type
Dier
Datasheet
1.220189-1.pdf (5 pages)

Specifications of 58330-1

Connector Type
BNC, TNC
Crimp Handle
A9996-ND
Product
Tool Component
Features
Die for Pro-Crimper
Lead Free Status / RoHS Status
Not applicable / Not applicable
Crimp Or Cable Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With
50 Ohm RF Connectors
Other names
A24779
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
1. INTRODUCTION
This instruction sheet covers the use and
maintenance of Crimping Die Assemblies listed in
Figure 1. The dies are used in PRO--CRIMPER III
Frame Assembly 354940--1 to crimp 50-- and
75--Ohm BNC, and 50--Ohm TNC Dual--Crimp
Connectors onto various size cable. Refer to Figure 1
for a list of connectors that are compatible with the
die assemblies. Refer to Catalog 82074 for additional
product part number information. For part numbers
not listed, contact TE Connectivity Product
Engineering for recommendations.
E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
Die Retaining Screws
Crimping Die
Assembly (Ref)
Indenter Die
Anvil Die
DIE ASSEMBLY PART NUMBER
Center Contact
Crimping Chamber
220189--1, 220189--2
220189--3
58330--1
Crimping Die Assemblies
220189- [ ] and 58330- 1
Ferrule Crimping
Chamber
Moveable
Jaw
TOOLING ASSISTANCE CENTER 1--800--722--1111
PRODUCT INFORMATION 1--800--522--6752
Stationary Jaw
Figure 1
Reasons for reissue are provided in Section 8,
REVISION SUMMARY.
2. DESCRIPTION
Each die assembly consists of an indenter die and an
anvil die, which when mated form two crimping
chambers. The large crimping chamber crimps the
connector ferrule and the small crimping chamber
crimps the connector center contact. Each die is held
in the tool by a single screw. See Figure 1.
NOTE
i
CONNECTOR BASE PART NUMBER
227000, 227079, 228980, 228979
225395, 225396, 225397, 225398
All dimensions in this document are in millimeters
[with inches in brackets]. Figures and Illustrations
are for reference only and are not drawn to scale.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
227079
PRO- - CRIMPER* III
Frame Assembly
354940- - 1 (Ref)
Instruction Sheet
408- - 2786
03 MAY 11 Rev J
1 of 5
LOC B

58330-1 Summary of contents

Page 1

... Crimping Die Assemblies 220189 and 58330- 1 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended- - use, production operations is available. ...

Page 2

DIE INSTALLATION To be sure that the die assembly is properly aligned during installation, proceed as follows: 1. Slide the die assembly into the partially--opened tool jaws. The anvil die must be installed in the movable jaw of the ...

Page 3

Slide the ferrule forward over the braid until the ferrule butts against the shoulder on the connector body. 3. Place the ferrule in the ferrule crimping chamber of the anvil die so that the shoulder on the connector body ...

Page 4

... REPLACEMENT Parts listed in Figure 6 are customer--replaceable. A complete inventory can be stocked and controlled to prevent lost time when replacement of parts is neces- sary. Order replacements through your local TE ...

Page 5

... WEIGHT: 227 g [8 oz] DIE ASSEMBLY PART NO. 220189--1 220189--2 220189--3 58330--1 Rev J 30.48 mm [1.20 in CUSTOMER- - REPLACEABLE PARTS ANVIL (Item 1) 310498--2 310498--4 310567--1 313764--1 Figure 6 408- 2786 11.89 mm [.468 in.] INDENTER (Item 2) 310497--2 310497--4 310568--1 313763-- ...