91910-2 Tyco Electronics, 91910-2 Datasheet

91910-2

Manufacturer Part Number

91910-2

Description

TOOL DIE SET PREMIUM COAXICON

Manufacturer

Tyco Electronics

Series

Pro-Crimper III, Coaxicon™r

Datasheet

1.1424050-1.pdf (4 pages)

Specifications of 91910-2

Connector Type

Crimp Terminals

Crimp Handle

A9996-ND

Lead Free Status / RoHS Status

Not applicable / Not applicable

Crimp Or Cable Size

Available stocks

Company

Part Number

Manufacturer

Quantity

Price

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

91910-21109

Manufacturer:

Amphenol FCI

Quantity:

12 000

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

91910-21109LF

Manufacturer:

FCI

Quantity:

455

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

91910-21109LF

Manufacturer:

Amphenol FCI

Quantity:

2 393

Company:

Meier Automation Equipment Co., Limited

Part Number:

91910-21109LF

Manufacturer:

FCI

Quantity:

20 000

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

91910-21111

Manufacturer:

Amphenol FCI

Quantity:

12 000

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

91910-21111LF

Manufacturer:

FCI

Quantity:

500

Company:

Meier Automation Equipment Co., Limited

Part Number:

91910-21111LF

Manufacturer:

FCI

Quantity:

20 000

Current page: 1 of 4
Download datasheet (237Kb)

The SDE crimping die assemblies listed in Figure 1

are designed to crimp the products also listed in

Figure 1. The die assembly must be installed into

PRO–CRIMPER* III Frame Assembly 354940–1.

Refer to instruction sheet 408–9930 for information on

the hand tool frame.

Reasons for reissue of this instruction sheet are

provided in Section 8, REVISION SUMMARY.

Dimensions in this instruction sheet are in metric

units [with U.S. customary units in brackets].

Figures are not drawn to scale.

Figure 1

Each four–piece die assembly consists of two

indenter dies and two anvil dies. When closed, the die

assembly forms two or three crimping chambers. The

larger crimping chambers crimp the ferrule of the

connector onto the coaxial cable, and the smaller

crimping chamber crimps the center contact onto the

center conductor of the coaxial cable. Each set of

dies is held in the tool frame by two pins and a screw.

1. Close the tool handles until the ratchet releases,

then allow the tool handles to open fully.

2. Remove the two die retaining screws and four

die retaining pins from the tool jaws.

3. Install the anvil dies in the movable jaw of the

tool frame so that the chamfered edges and

marked surfaces face outward. Align the dies with

the screw hole, then insert the two die retaining

pins included with the die assembly through the

holes in the dies and into the holes in the tool

frame.

4. Secure the anvil dies with the die retaining

screw included with the die assembly. DO NOT

fully tighten the screw.

5. Install indenter dies in the stationary jaw of the

tool frame so that the chamfered edges and

marked surfaces face outward. Align the dies with

the screw hole, then insert the two die retaining

pins included with the die assembly through the

holes in the dies and into the holes in the tool

frame.

6. Secure the indenter dies with the die retaining

screw included with the die assembly. DO NOT

fully tighten the screw.

7. Slowly close the tool handles, making sure that

the dies align properly. After the anvil dies enter

the indenter dies, place a 1.57+0.05–mm

[.062+.002–in.] diameter copper bus bar into the

center contact crimping chamber of the die

assembly.

8. Continue closing the tool handles until the

ratchet has engaged sufficiently to hold the dies in

place, then tighten both die retaining screws.

The ratchet has detents with audible clicks" as

the handles are closed. The ratchet releases on

the sixth click."

91910-2 Summary of contents

Page 1

Figure 1 The SDE crimping die assemblies listed in Figure 1 are designed to crimp the products also listed in Figure 1. The die assembly must be installed into PRO–CRIMPER* III Frame Assembly 354940–1. Refer to instruction sheet 408–9930 for ...

Page 2

... SDE Crimping Die Assemblies 91902-1, 91907-[ ], 91908-1, 91909-1, 91910-[ ], and 1424050 remove the die assembly from the tool frame, close the tool handles until the ratchet releases, remove the two die retaining screws and four die retaining pins, and slide the dies out of the jaws. ...

Page 3

... Measure the die opening to ensure that it meets the dimensions given in Figure 5. Lockscrew Order replacements through your local representative, or call 1–800–526–5142, or send a facsimile of your purchase order to 1–717–986–7605, or write to: CUSTOMER SERVICE (038–035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105–3608 Tyco Electronics Corporation of 4 ...

Page 4

... DIE ASSEMBLY DIE ASSEMBLY A 91902-1 1.93 [.076] 91907-[ ] 1.24 [.049] 91908-1 1.27 [.050] 1.257-1.321 91909-1 [.050-.052] 1.219-1.283 91910-2 [.048-.051] 91910-[ ] 1.219-1.283 (Except -2) [.048-.051] 1424050-1 1.12 [.044] 8. REVISION SUMMARY Revisions to this instruction sheet include: S Updated document to corporate requirements +0.03 [.001] ...