47821 Tyco Electronics, 47821 Datasheet - Page 2

• Manufacturer Part Number: 47821
• Description: DIE TERMINYL 69051 6AWG
• Manufacturer: Tyco Electronics

Specifications of 47821

• Lead Free Status / RoHS Status: Not applicable / Not applicable

of 8
7. Activate the tool or power unit to allow the ram
to return to the “down” position.
8. Close the yoke, and insert the latch pin.
1. Remove latch pin and open yoke on crimping
head.
2. Loosen the setscrew in the yoke, and remove
the stationary die.
3. Extend the ram until the ram setscrew is visible.
4. Loosen setscrew in ram. Remove moving die.
1. Strip wire to the dimensions listed in Figure 3.
Do not nick or cut the wire strands.
2. Select the proper color–coded terminal for the
wire size. The wire size stamped on the terminal
tongue and on the crimping die must match the
wire size selected.
Wire Strip Length
1/0
2/0
3/0
4/0
8
6
4
2
!
18.54-20.24 [.730-.797]
18.54-20.24 [.730-.797]
19.05-20.64 [.750-.813]
19.45-21.03 [.766-.828]
11.18-12.70 [.440-.500]
11.18-12.70 [.440-.500]
11.43-13.08 [.450-.515]
7.96-9.53 [.313-.375]
To avoid damage to the dies, be sure that the
moving and stationary dies are properly oriented.
Avoid personal injury. When operating tool or
power unit, exercise caution while holding
terminals or wire near the crimping area.
Typical Terminal
15.48-17.07
20.24-19.45
19.45-21.03
21.83-30.18 [.859-1.188]
28.58-30.18 [1.125-1.188]
28.58-30.18 [1.125-1.188]
28.58-30.18 [1.125-1.188]
28.58-30.18 [1.125-1.188]
[.609-.672]
[.797-.766]
[.766-.828]
Tyco Electronics Corporation
Wire Strip Length
Figure 3
10.72-12.29 [.422-.484]
13.10-14.68 [.516-.578]
21.83-23.42 [.859-.922]
3. Insert stripped wire fully into terminal wire barrel.
The end of the conductor must not protrude more
than 1.60 mm [.063 in.] beyond the edge of the
wire barrel.
4. Remove crimping head latch pin and open yoke.
5. Place the terminal in the stationary die with the
edge of the wire barrel resting against the locator
and the bottom of the terminal tongue facing the
stationary die. See Figure 4.
6. Holding the terminal in place, close the yoke and
insert the latch pin.
7. Holding wire in place, activate tool or power unit
to complete crimp.
8. When crimp is completed, remove the latch pin,
open the yoke, and remove the terminal.
9. Inspect the crimp according to Section 5.
!
!
i
--
--
--
--
--
(Without Step-Down Adapter)
Do NOT turn or twist the wire or terminal during
insertion.
Be sure that the latch pin is fully inserted,
otherwise damage to the die and tool or head will
occur when the tool or power unit is activated.
If terminal sticks in die after crimping, apply a
rocking action to the terminal to remove it from
the die. Wipe light oil on the dies to prevent
sticking, or use spray dry lubricant.
Typical Splice
É É É
É É É É É É
Ç Ç Ç Ç
Ç Ç Ç Ç É É É
15.47-16.26 [.609-.640]
15.47-16.26 [.609-.640]
18.68-21.83 [.735-.859]
18.68-21.83 [.735-.859]
19.05-21.83 [.750-.859]
19.45-20.64 [.766-.813]
11.51-12.29 [.453-.484]
11.51-12.29 [.453-.484]
Wire Stop
Window Indent
Rev