11-01-0204 Molex Inc, 11-01-0204 Datasheet

TOOL HAND CRIMP 2MM CONTACTS

11-01-0204

Manufacturer Part Number
11-01-0204
Description
TOOL HAND CRIMP 2MM CONTACTS
Manufacturer
Molex Inc
Series
Milli-Grid™r
Datasheets
1.64016-0201.pdf (1 pages)
2.63811-1600.pdf (24 pages)
3.11-01-0204.pdf (1 pages)
4.11-01-0204.pdf (5 pages)

Specifications of 11-01-0204

Tool Type
Hand Crimper
Features
Side Entry, Ratchet
For Use With/related Products
Rectangular Contacts, 24-30 AWG
Lead Free Status / RoHS Status
Not applicable / Not applicable
Other names
0011-01-0204
0011-01-0204-E
0011010204
0011010204-E
11-01-0204-E
11010204
11010204-E
CR60927A
WM18057
Hand Crimp Tool for Milli-Grid™ Crimp Terminal
Doc No: ATS-011010204
Revision: E
FEATURES
SCOPE
Products: Milli-Grid™ Crimp Terminal for 24-30 AWG.
DEFINITION OF TERMS
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the
scope.
Series No.
Terminal
50394
Small handle spread which make this style tool ideally suited for end users
Ratchet with safety release that ensures consistent performance
A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position
BRUSH
LENGTH
STRIP
50394-8100 50394-8400 50394-8051 50394-8054
50394-8200
Loose Piece
Terminal Order No.
Customer to cut off terminal from reel: 0.20mm (.008”) maximum Cut-off Tab.
Release Date: 03-02-93
Revision Date: 04-14-08
50394-8052
BELL MOUTH
Engineering No. CR60927A
SPECIFICATION SHEET
INSULATION
Order No. 11-01-0204
HAND CRIMP TOOL
Reel
CRIMP
UNCONTROLLED COPY
CONDUCTOR
AWG
24-30 0.20-0.05 0.80-1.40 .031-.055 1.30-1.80 .051-.071
CRIMP
Wire Size
mm²
CRIMP HEIGHT
Insulation Diameter
mm
In.
BEND UP
DOWN
BEND
mm
Strip Length
TWISTING
ROLLING
Page 1 of 5
In.

11-01-0204 Summary of contents

Page 1

... The above terminal drawing is a generic terminal representation not an image of a terminal listed in the scope. Doc No: ATS-011010204 Release Date: 03-02-93 Revision: E Revision Date: 04-14-08 HAND CRIMP TOOL SPECIFICATION SHEET Order No. 11-01-0204 Engineering No. CR60927A Wire Size Reel AWG mm² 24-30 0.20-0.05 0.80-1.40 .031-.055 1.30-1.80 .051-.071 50394-8052 ...

Page 2

... Partially close the tool until the terminal is held in place. See Figure 1. CONDUCTOR LOCATOR BLADE INSULATION TERMINAL Figure 2 LOCATOR Note: The tamper proof ratchet action will not release the tool until it has been fully closed. Doc No: ATS-011010204 Release Date: 03-02-93 Revision: E Revision Date: 04-14-08 Conductor Crimp Height (Ref) Width (Ref In. ...

Page 3

... This tool is designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty. Hand held crimping tools are intended for low volume, prototyping, or repair requirements only. Caution: Repetitive use of this tool should be avoided. Doc No: ATS-011010204 Release Date: 03-02-93 Revision: E Revision Date: 04-14-08 ...

Page 4

... Molex does not certify crimp hand tools. CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling. Doc No: ATS-011010204 Release Date: 03-02-93 Revision: E Revision Date: 04-14-08 UNCONTROLLED COPY ...

Page 5

... M4 NUT 1 LOCATOR BLADE Americas Headquarters Far East North Headquarters Lisle, Illinois 60532 U.S.A. Yamato, Kanagawa, Japan 1-800-78MOLEX 81-462-65-2324 amerinfo@molex.com feninfo@molex.com Doc No: ATS-011010204 Release Date: 03-02-93 Revision: E Revision Date: 04-14-08 Order Number Description 11-11-0381 Locator Assembly** 11-11-0324 Spring (Main) 11-11-0320 Spring (Ratchet) ...