64001-3900 Molex Inc, 64001-3900 Datasheet - Page 6

• Manufacturer Part Number: 64001-3900
• Description: TOOL HAND CRIMP FOR TERMINALS
• Manufacturer: Molex Inc
• Series: Insulkrimp®, Nylakrimp®, Perma-Seal™, Versakrimp™r
• Type: Crimp Tool Assemblyr

Specifications of 64001-3900

• Features: Side Entry, Ratchet
• Tool Type: Hand Crimper
• Fits Cable/wire: 8-2 AWG
• Product: Crimping, Stripping & Cutting Tools & Drills
• Description/function: Hand crimp tool assembly
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: Splices and Terminals, 2-8 AWG
• For Use With: WM19139 - CONN RING TERM 2AWG 5/16" CRIMPWM19138 - CONN RING TERM 2AWG 3/8" CRIMPWM19137 - CONN RING TERM 2AWG 1/4" CRIMPWM19136 - CONN RING TERM 2AWG 1/2" CRIMPWM19135 - CONN RING TERM 4AWG 1/2" CRIMPWM19134 - CONN RING TERM 4AWG 1/4" CRIMPWM19133 - CONN RING TERM 4AWG #10 CRIMPWM19132 - CONN RING TERM 4AWG 5/16" CRIMPWM19131 - CONN RING TERM 4AWG 3/8" CRIMPWM19130 - CONN RING TERM 4AWG 1/4" CRIMPWM19129 - CONN RING TERM 6AWG 1/4" CRIMPWM19128 - CONN RING TERM 6AWG #10 CRIMPWM19127 - CONN RING TERM 6AWG 1/2" CRIMPWM19126 - CONN RING TERM 6AWG 5/16" CRIMPWM19125 - CONN RING TERM 6AWG 3/8" CRIMPWM19124 - CONN RING TERM 6AWG 1/4" CRIMPWM19123 - CONN RING TERM 8AWG #10 CRIMPWM19122 - CONN RING TERM 8AWG 5/16" CRIMPWM19121 - CONN RING TERM 8AWG 3/8" CRIMPWM19120 - CONN RING TERM 8AWG 1/4" CRIMPWM19119 - CONN RING TERM 8AWG #10 CRIMPWM18727 - CONN SPLICE SEALABLE 8AWG
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 064001-3900; 064001-3900-E; 0640013900; 0640013900-E; 64001-3900-E; 640013900; 640013900-E; WM19140

MCT-8200 Hand Crimp Tool
Doc. No: ATS-640013900
Revision: K
Miscrimps or Jams
Should this tool ever become stuck or jammed in a partially closed position,
The tool will open easily by pushing the ratchet release lever forward. See Figure 6.
How to Adjust Tool Preload
Over the life of the tool, it may be necessary to adjust tool handle preload force. Listed below are the steps
required to adjust the crimping force of the hand tool to obtain proper crimp conditions:
1. Close the tool handles until jaws are fully closed and
2. If tool needs adjustment, turn the preload adjustment
3. Recheck the preload after making a crimp. Check the
Tool Calibration
A Certificate of Calibration (see last page) was supplied with the tool. To
recalibrate this tool, pin gauge measurements should be taken in each
conductor nest and compared to this chart. The tool should be lubricated
before recalibration to ensure consistent measurements. Handle preload is
factory set to 30-35 LBS. See How to Adjust Tool Preload, see Figure 7 to
recalibrate.
not under pressure. Put one handle grip on a weight
scale and apply pressure downward against opposite
handle. Observe the highest-pressure reading.
screw. To increase preload setting, tighten (CW) the
screw slightly, to decrease loosen (CCW) the screw.
The preload should be 30-35 LBS.
crimp specifications after tool handle preload force is
adjusted.
Release Date: 09-26-03
Revision Date: 05-06-08
AWG pin gauge readings are taken from nests marked “INS.”
(See Figure 6 and 7)
Wire Range
AWG
8
6
4
2
10.00
16.00
25.00
35.00
mm²
“X” Dimension Conductor Crimp
Mean
.170
.240
.330
.378
ADJUSTMENT
UNCONTROLLED COPY
PRELOAD
SCREW
Figure 6
.165
.235
.325
.373
Go
Figure 7
JAWS FULLY
CLOSED
No Go
.176
.246
.336
.384
Do Not force the handles open or closed.
FORWARD TO RELEASE
RATCHET RELEASE
“CONFINING” CRIMP
LEVER PUSH
PRELOAD ADJUSTMENT
HANDLE GRIPS
SCREW
CONDUCTOR CRIMP
PIN GAUGE IN
Page 6 of 9
X