58517-1 Tyco Electronics, 58517-1 Datasheet - Page 2

• Manufacturer Part Number: 58517-1
• Description: TOOL CRIMP W/DIE CST-100
• Manufacturer: Tyco Electronics
• Series: Pro-Crimper™ IIIr
• Type: Hand Tool Assemblyr

Specifications of 58517-1

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Rohs Compliant: NA
• Product: Crimping, Stripping & Cutting Tools & Drills
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Rectangular Contacts, 22-26 AWG
• For Use With: 1445336-3 - CONTACT CST-100 II 26-22AWG 30AU1445336-2 - CONTACT CST-100 II 26-22AWG 15AUA99620 - CONN SCKT 26-22AWG TIN CST100 IIA23962 - CONN SOCKET 22-26AWG GOLD CRIMPA19520 - CONN TERM CRIMP CST-100 TIN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A19530

Rev E
Die retaining pins and die retaining screws are used to
position and secure the dies in the tool frame. A
washer and nut is used on the lower die retaining
screw to hold the locator in place.
3. INSTALLATION AND REMOVAL OF DIE SET AND
LOCATOR ASSEMBLY
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil in the
moving jaw so that their chamfered sides and
their marked surfaces face outward, when
mounted in the moving jaw of the tool frame.
3. Insert the two die retaining pins.
4. Insert the long die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do
not tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper
in the stationary jaw so that their chamfered sides
and their marked surfaces face outward, when
mounted in the stationary jaw of the tool frame.
6. Insert the two die retaining pins.
7. Insert the short die retaining screw through the
jaw and through both crimper dies, and tighten
the screw just enough to hold the dies in place.
Do not tighten the screw completely at this time.
Chamfer
Offset
Wire
Crimper
Nut
Washer
Wire Anvil
Locator
(Figure 2)
Adjustment
Screw
Insulation
Crimper
Nut
Chamfer
Figure 2
Insulation
Anvil
4. CRIMPING PROCEDURE
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Place the locator over the end of the long
screw, and position the locator against the side of
the tool jaw.
10. Place the washer and nut onto the end of the
long screw. Align the locator slot with the
crimping section and carefully tighten the nut.
11. To disassemble, close the tool handles until
the ratchet releases, remove the nut, the washer,
the locator, the two die retaining screws, and the
four die retaining pins, and slide the anvils and
crimpers out of the tool jaws.
NOTE
i
This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be verified
as specified in Figure 4. Refer to Section 6, Crimp
Height Inspection, and Section 7, Crimp Height
Adjustment, to verify crimp height before using the
tool to crimp desired contacts and wire sizes.
Die Retaining Screws
Tool Frame
(or Bench
Machine, or
Ratched Hand
Tool)
408-4064
Die
Retaining
Pins
2 of 5