58514-1 Tyco Electronics, 58514-1 Datasheet

PROCRIMP TL W/DIE MR18-26

58514-1

Manufacturer Part Number
58514-1
Description
PROCRIMP TL W/DIE MR18-26
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ III, MRr
Type
Crimp Toolr
Datasheet
1.58514-1.pdf (6 pages)

Specifications of 58514-1

Tool Type
Hand Crimper
Features
Side Entry, Ratchet
Rohs Compliant
NA
Product
Crimping, Stripping & Cutting Tools & Drills
Description/function
PRO-CRIMPER III Hand Tool
Lead Free Status / RoHS Status
Not applicable / Not applicable
For Use With/related Products
Rectangular Contacts, 18-26 AWG
For Use With
350666-1 - CONN SOCKET 18-26AWG CRIMP TINA25442 - CONN PIN GRND 18-26AWG TIN CRIMPA25445 - CONN SOCKET 24-26AWG GOLD CRIMPA25441 - CONN SOCKET 24-26AWG TIN CRIMPA25444 - CONN PIN 24-26AWG GOLD CRIMPA25446 - CONN PIN 18-26AWG GOLD CRIMPA25440 - CONN PIN 24-26AWG TIN CRIMPA14196 - CONN SOCKET 18-26AWG GOLD CRIMPA14197 - CONN SOCKET 18-26AWG TIN CRIMPA14198 - CONN PIN 18-26AWG GOLD CRIMPA14199 - CONN PIN 18-26AWG TIN CRIMP
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
58514-1
A25448
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
1. INTRODUCTION
PRO--CRIMPER III Hand Crimping Tool Assembly
58514--1 consists of Die Assembly 58514--2 and
PRO--CRIMPER III Hand Crimping Tool Frame
354940--1. The die assembly consists of crimping
dies and a locator assembly.
Read these instructions thoroughly before crimping
The PRO- - CRIMPER III Hand Crimping Tool is a “Commercial” grade tool
and is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 series specification, but may not comply with other feature
parameters of the specification. Tyco Electronics offers a variety of tools to
satisfy your performance requirements. For additional information, contact the
Tooling Assistance Center at 1- - 800- - 722- - 1111.
E2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
{
}
Assembly
SUPPLIED WITH THE DIE ASSEMBLY. ALSO AVAILABLE SEPARATELY.
CALL THE TOOLING ASSISTANCE CENTER OR PRODUCT INFORMATION (SEE BELOW) FOR PRODUCT PART NUMBERS.
58514--2
TE Die
TE Die
Front of Tool
(Locator Side)
Locator Assembly
(Supplied with
Die Assembly)
TE Locator
TE Locator
Assembly
58515--1
Die
Assembly
{
Moving Jaw
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
Ratchet
Adjustment
Wheel
PRO- CRIMPER* III Hand
Crimping Tool Assembly 58514- 1
with Die Assembly 58514- 2
Rectangular
Mi i t
Miniature
Contacts
Contacts
Contact
Contact
Family
}
Figure 1
any contacts.
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
NOTE
i
(AWG)
26--22
20--18
26--24
Size
Stationary Jaw
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
Pivot Pin
Moving Handle
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
[.025 to .050]
[ 050 t 115]
[.050 to .115]
1.27 to 2.92
.64 to .127
Insul Dia
Wire
Back of Tool
(Wire Side)
PRO- - CRIMPER III Hand
Crimping Tool Frame
354940- - 1 (408- - 9930)
Stationary
Handle
Instruction Sheet
408- - 9973
28 SEP 09 Rev B
[.156 +/-- .015]
[.156 +/-- .015]
Strip Length
3.96 +/-- .380
(mm [In.])
1 of 6
LOC B

58514-1 Summary of contents

Page 1

... CALL THE TOOLING ASSISTANCE CENTER OR PRODUCT INFORMATION (SEE BELOW) FOR PRODUCT PART NUMBERS. 1. INTRODUCTION PRO--CRIMPER III Hand Crimping Tool Assembly 58514--1 consists of Die Assembly 58514--2 and PRO--CRIMPER III Hand Crimping Tool Frame 354940--1. The die assembly consists of crimping dies and a locator assembly. ...

Page 2

... To disassemble, close the tool handles until the ratchet releases, remove the nut, the locator assembly, the two die retaining screws, and the four die retaining pins, and slide the anvils and crimpers out of the tool jaws. Tyco Electronics Corporation Tool Frame Die Retaining Pins Die Retaining ...

Page 3

... Make sure that both sides of the insulation barrel CAUTION are started evenly into the crimping section NOT attempt to crimp an improperly positioned contact. Back of Tool (Wire Side) Contact (Typ) Locator Wire in Wire Stop Slot Figure 3 Tyco Electronics Corporation Strip Length Wire Inserted to Stop ...

Page 4

... CRIMP HEIGHT INSPECTION RATCHETCrimp height inspection is performed through the use of a micrometer with a modified anvil, commonly referred crimp--height comparator. Tyco Electronics does not manufacture or market crimp--height comparators. Detailed information on obtaining and using crimp--height comparators can be found in instruction sheet 408--7424. ...

Page 5

... Revisions to this instruction sheet include: Change PRO--CRIMPER II Hand Tool to S PRO--CRIMPER III Hand Tool; Revised crimp--height inspection information; S Applied TE logo; S Updated format to current corporate S requirements; and Added back page to illustrate tooling S compatible with die set 58514--2. Tyco Electronics Corporation ...

Page 6

... Die Assembly 58514- 2 Can Be Used In the Following Tools: PRO- CRIMPER III Hand Tool 354940- 1 (Instruction Sheet 408- 9930) SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052) Battery Tool (Shouldered Die) 1725837 (Customer Manual 409- 10053 SDE PEW- 12 Hand Tool 9- 1478240- 0 (Instruction Sheet 408- 8851) ...