LCC110STR Clare, LCC110STR Datasheet
LCC110STR
Specifications of LCC110STR
LCC110STR
Available stocks
Related parts for LCC110STR
LCC110STR Summary of contents
Page 1
... UL Recognized Component: File E76270 • CSA Certified Component: Certificate 1175739 • EN/IEC 60950-1 Certified Component: TUV Certificate 49410 004 Ordering Information Part # LCC110 LCC110P LCC110PTR LCC110S LCC110STR Pin Configuration AC/DC Configuration 1 Do Not Use 2 + Control 3 – Control 4 Do Not Use Switching Characteristics for a ...
Page 2
... A 150 mW 800 rms +85 ºC +125 ºC Conditions Symbol - I L t=10ms I LPK I =120mA =350V LEAK =8mA, V =10V off V =50V, f=1MHz C L OUT I =120mA =8mA = I/O www.clare.com LCC110 Min Typ Max Units - - 120 350 Ω µ 0.4 0 0.9 1.2 1.4 V μ R05 ...
Page 3
... Turn-Off (ms) Form-A Typical I for Switch Dropout F (N=50, I =120mA , T =25º 1.2 2.0 2.8 3.6 4.4 LED Current (mA) www.clare.com Typical Leakage vs. Temperature Measured across Pins 5&6 or 7&8 0.020 0.018 0.016 0.014 0.012 0.010 0.008 0.006 0.004 0.002 0 120 -40 - Temperature (ºC) 100s Form-A ...
Page 4
... Load Voltage (V) Form-A Typical Blocking Voltage vs. Temperature 420 415 410 405 400 395 390 385 380 375 -40 - Temperature (ºC) www.clare.com LCC110 Form-A Typical I for Switch Operation F vs. Temperature (I =120mA ) -40 - Temperature (ºC) Form-A Typical Turn-Off vs. Temperature (I =5mA, I =120mA ...
Page 5
... LED Forward Current (mA) Form-B Typical Turn-On vs. Temperature (I =5mA, I =120mA ) 0.25 0.20 0.15 0.10 0.05 0 -40 - 100 Temperature (ºC) www.clare.com Form-B Typical On-Resistance Distribution (N=50, I =8mA, I =120mA , 0.56 25.5 26.5 27.5 28.5 29.5 30.5 On-Resistance (Ω) Form-B Typical Blocking Voltage Distribution (N=50, T =25º ...
Page 6
... Load Voltage (V) Form-B Typical Blocking Voltage vs. Temperature 420 415 410 405 400 395 390 385 380 -40 - Temperature (ºC) www.clare.com Form-B Typical Load Current vs. Temperature (I =8mA) F 180 160 140 120 100 -40 - Temperature (ºC) 100 LCC110 100 120 R05 ...
Page 7
... Clare recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since Clare employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. ...
Page 8
... LCC110 PCB Hole Pattern 8-0.800 DIA. 2.540 ± 0.127 (8-0.031 DIA.) (0.100 ± 0.005) 6.350 ± 0.127 (0.250 ± ...
Page 9
... The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage ...