HW-MP-PC44-1 Xilinx Inc, HW-MP-PC44-1 Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
HW-MP-PC44-1
Manufacturer Part Number
HW-MP-PC44-1
Description
ADAPTER 44-PLCC XC18V00 PROM
Manufacturer
Xilinx Inc
Datasheet
1.HW-MULTIPRO.pdf
(12 pages)
Specifications of HW-MP-PC44-1
Accessory Type
Programming Adapter
For Use With/related Products
XC18V04 44-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
IEEE 1284 Cable Specifications
Level 1 compliant host parallel ports are only designed to
operate over a maximum cable length of 10 feet. Level 2
compliant ports are designed to operate over a maximum
cable length of 33 feet. MultiPRO uses a Level 2 compliant
cable interface buffer. The MultiPRO case has an integrated
mini-centronics connector for attachment to off-the-shelf
IEEE 1284 cables.
Xilinx recommends that the MultiPRO tool be directly
connected to the host parallel port without the use of a switch
box. Software license "dongles" should not be attached to the
parallel port when communicating with the MultiPRO tool.
Automatic Voltage Sensing
The MultiPRO Desktop Tool continuously monitors the V
pin on the Serial/JTAG/SPI and SelectMAP target interface
connectors. The current drain from the target power supply
attached to the V
target system reference voltage must be regulated and
cannot have a current limiting resistor in series with the
V
No damage will occur to the MultiPRO Desktop Tool if the
target system is powered when the MultiPRO tool is not
powered. However, when powering up a system, it is
preferable to apply power to the MultiPRO tool first, followed
by power to the target system. The sequence should be
reversed when powering down.
The MultiPRO Desktop Tool always puts interface signals
on inactive ports in a 3-state condition.
The MultiPRO output drive voltage levels do not linearly
track voltage changes on the V
output signal level is established for a range of V
voltages. For example, if V
to +5.0V DC, the MultiPRO tool sets the output signals for
the respective port to +3.3V DC.
Refer to
and MultiPRO output signal levels.
Table 2: Output Signal Levels as a Function of V
.
DS114 (v1.9) February 8, 2008
Product Specification
REF
V
REF
pin on the interface.
Voltage on Target
0.80 to 1.65
1.65 to 2.00
2.00 to 3.00
3.00 to 5.00
Table 2
System
R
for the relationship between V
REF
pin is less than 10 mA at 3.3V DC. The
REF
MultiPRO Output
is any voltage from +3.0V DC
Signal Levels
REF
pin. An appropriate
1.5
1.8
2.5
3.3
REF
REF
voltage
Units
REF
V
V
V
V
www.xilinx.com
REF
Connecting to Host Computer
The MultiPRO tool connects to any PC using Windows or
Linux
(printer) port connector
this cable, the host PC must have a parallel port that is
enabled
ECP mode is not enabled, the MultiPRO tool will default to
compatibility mode and will not run at the optimum speeds
listed. Performance also depends on the MultiPRO Desktop
Tool firmware revision and ISE iMPACT software version.
Notes:
1.
2.
3.
4.
High Performance Ribbon Cable
Two insulation displacement connector (IDC) ribbon cables
are supplied and recommended for connection to target
systems. See
multiple signal-ground pairs and facilitate error-free
connection. A very small footprint, keyed mating connector is
all that is required on the target system. Refer to
Figure 8
sample vendor part numbers. The 14-conductor ribbon cable
can also be used with Parallel Cable IV.
X-Ref Target - Figure 5
Refer to
operating systems.
Xilinx makes no representations about compatibility with third-
party IEEE 1284 add-on adapters and does not support the add-
on adapters.
Refer to host PC BIOS to see if ECP mode is enabled.
Refer to the MultiPRO Desktop Tool firmware history at
http://www.xilinx.com/support/programr/mp_history.htm.
1
Figure 5: High Performance Ribbon Cables
through the built-in, standard IEEE 1284 DB25 parallel
3
for the appropriate connector pin assignments and
to support extended capability port (ECP) mode. If
ISE software manuals
Figure 5
and
2
. To fully utilize the higher speeds of
Figure
for details regarding supported
6. These cables incorporate
MultiPRO Desktop Tool
Figure 7
and
4
4