C8051F040DK-J Silicon Laboratories Inc, C8051F040DK-J Datasheet - Page 5

• Manufacturer Part Number: C8051F040DK-J
• Description: DEV KIT FOR F040/F041/F042/F043
• Manufacturer: Silicon Laboratories Inc

Specifications of C8051F040DK-J

• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

5.3. Controller Area Network (CAN) Application Example
Configuration and use of the CAN controller is documented in the Bosch CAN User’s Guide, located in the “Documen-
tation” directory on the CD-ROM. Accessing the CAN controller (i.e., accessing the CAN RAM, CAN registers, and
moving data to and from the CAN controller) is documented in Silicon Laboratories’ C8051F04x data sheet.
An example CAN application is included in the “Examples\C8051F04x” directory. Each C8051F040 target board fea-
tures a push button (labeled P3.7) and a LED (labeled P1.6). After the two target boards are connected together via
the provided CAN bus physical layer (i.e. cable, connectors, and CAN transceiver), the example application sends
CAN messages between the two target boards containing the state of the push buttons. In this example, each CAN
controller has two of the 32 message objects configured: one to send a control signal based on the state of its target
board push button, and one to receive a control signal from the other target to see if it should turn on/off its own LED.
When a target board receives a message that the push button on the other target board is depressed, it lights its own
LED. When a target board receives a message that the push button on the other target board is not depressed, it
turns off its own LED. In this way, the push button on one target board controls the LED on the other target board as
a virtual control link via a CAN bus.
5.3.1. Setting-up the Application
You should now have can1.c loaded into Target Board #1, and can2.c loaded into Target Board #2. The CAN cable
should be connected to both boards at the CAN DB-9 connectors.
5.3.2. Running the Application
Once this example is running, you have established a simple CAN network with two nodes. When one C8051F040
device senses the push button on its target board is pressed, it sends a “0x11” in the first byte of a CAN message
data field. When the button is released, the first byte of the CAN message data field is “0x00”. When a C8051F040
device receives a message, it checks whether this byte has a value of “0x11” or “0x00”. When the byte is “0x11”,
the device turns on its LED by setting P1.6 high. When the byte is “0x00”, the device turns off its LED by setting
P1.6 low.
1. Connect the target boards together at the CAN DB-9 connectors using the CAN cable provided in the
2. Compile and link the can1.c example located in the “Examples\C8051F04x” directory on the CD-ROM.
3. Connect the Debug Adapter to the other target board, Target Board #2. Open a new project in the IDE and
1. Start the application by resetting the device on each target board. Do this by depressing the RESET push
2. Pressing the P3.7 push button on Target Board #1 will light the LED on Target Board #2. Likewise, when
development kit, as shown in Figure 2 on page 6. The correct cable has a male connector on both ends.
Take care not to connect the CAN cable to the RS232 DB-9 connector. See Figure 3 on page 7 for the
location of the CAN DB-9 connector.
Choose one of the target boards as Target Board #1. Connect to Target Board #1 and download the can1
project to the C8051F040, following the steps outlined in Section 4.4 on page 2. Once downloaded, close
this project in the IDE and disconnect the Debug Adapter from Target Board #1.
load can2.c into the C8051F040 device, just as was done in step 2 for Target Board #1. Take care not to
load can1.c into both devices. Disconnect the Debug Adapter from this board.
button on each target board. As can1.c executes on Target Board #1, and can2.c runs on Target Board #2,
the devices are now nodes on a CAN bus.
the push button on Target Board #1 is released, the LED on Target Board #2 will turn off. This will work on
either target board.
Rev. 0.6
C8051F04x-DK
5