PIIPM50P12B004X Vishay, PIIPM50P12B004X Datasheet - Page 3

• Manufacturer Part Number: PIIPM50P12B004X
• Description: IC PWR MODULE PROG ISO 50A 1200V
• Manufacturer: Vishay

Specifications of PIIPM50P12B004X

• Module/board Type: Programmer Module
• For Use With/related Products: Servo Motors
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

1
www.irf.com
To enable DSP boot ROM for boot load feature through SCI at 40Mhz clock operation follow these steps:
PIIPM50P12B004
Vin iso
GND iso
Tx+
Tx-
Rx+
Rx-
Enc1 – Hall1 / SpiCK
Enc2 – Hall2 / SpiSTE
SpiTx
Vin
COM
TMS
TMS2
TDI
TDO
TCK
TRST~
EMU0
EMU1/OFF~
PD
TCK_RET
Boot-En~
COM
Signal pins on RS422 serial port
Signal pins on IEEE1149.1 JTAG connector
~ indicates active low signals
Strb – Hall3 / SpiRx
1)
2)
3)
4)
Symbol
CAUTION DO NOT APPLY DC BUS VOLTAGE WHEN JTAG INTERFACE IS CONNECTED, SEVERE
Symbol
Connect Boot-En~ to COM;
Connect STR – Hall3 / SpiRx to GND iso;
Apply voltage to Vin iso;
Apply-voltage to Vin (after Vin iso to allow proper configuration).
JTAG test mode select
JTAG test mode select 2
JTAG test data input
JTAG test data output
JTAG test clock. TCK is a 10MHz clock source from the emulation pod.
This signal can be used to drive the system test clock.
JTAG test reset
Emulation pin 1
Presence detect.
Indicates that the emulation cable is connected and that the PI-IPM log ic is
powered up. PD is tied to the DSP 3.3V supply through a 1k resistor.
JTAG test clock return. Test clock input to the emulator.
Internally short circuited to TCK.
Boot ROM enable. This pin is sampled during DSP reset, pulling it low
enables DSP boot ROM (Flash version only). 47k internal pull-up. Please
see note below.
Exernal 15V supply ground reference. This pin is directly connected to DC-
Emulation pin 0
DAMAGE WILL OCCUR ON POWER MODULE AND ON YOUR EQUIPMENT!
External 5V supply voltage for opto-couplers and line driver supply
RS422 Trasmitter Non inverting Driver Output
RS422 Trasmitter Inverting Driver Output
RS422 Receiver Non inverting Driver Input,
RS422 Receiver Inverting Driver Input
Incremental Encoder 2 / Hall effect sensor input 2 / SpiSTE input (GND iso referenced)
Incremental Encoder Strobe / Hall effect sensor input 3 / SpiRx input (GND iso ref.)
Also used for DSP boot feature using DSP boot ROM. Please see note below.
SpiTx output (GND iso referenced)
External 15V supply voltage. Internally referred to DC bus minus pin (DC -)
External 15V supply ground reference. This pin is directly connected to DC -
Extenal 5V supply ground reference for opto-couplers and line driver supply
Incremental Encoder 1 / Hall effect sensor input 1/ SpiCK input (GND iso referenced)
I27146
1
06 - Oct
Lead Description
Lead Description
State
Output
Output
Output
Input
Input
Input
Input
Input
Input
N/A
I/O
I/O
9-10
5-6
7-8
12
14
13
15
11
16
17
20
Pin number
1
17-18
19-20
Pin number
10
6
7
1
2
4
3
5
9
8
IEEE1149.1
JTAG
RS422
serial
port
3