PIIPM50P12B004X Vishay, PIIPM50P12B004X Datasheet

Page 1

PI-IPM Features: Power Module: NPT IGBTs 50A, 1200V 10us Short Circuit capability Square RBSOA Low Vce (2.15Vtyp @ 50A, 25°C) (on) Positive Vce temperature coefficient (on) Gen III HexFred Technology Low diode V (1.78Vtyp @ 50A, 25°C) F Soft reverse ...

Page 2

PIIPM50P12B004 I27146 Detailed Block Diagram Com Boot-en~ Tck-ret TRST~ Tck TDo i TD TMS www.irf.com 06 - Oct Fault~ in01 C AD in00 C AD LFault 2 ...

Page 3

PIIPM50P12B004 I27146 Signal pins on RS422 serial port Symbol Vin iso External 5V supply voltage for opto-couplers and line driver supply GND iso Extenal 5V supply ground reference for opto-couplers and line driver supply Tx+ RS422 Trasmitter Non inverting Driver ...

Page 4

PIIPM50P12B004 I27146 Following pins are intended for signal communication between driving board and power module only, though here described for completeness, they are on purpose not available to the user. Symbol Bus plus input signal DC - ...

Page 5

PIIPM50P12B004 I27146 Absolute Maximum Ratings (T Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to V Thermal Resistance and Power Dissipation ratings are measured at still air ...

Page 6

PIIPM50P12B004 I27146 Electrical Characteristics: Inverter For proper operation the device should be used within the recommended conditions 25°C (unless otherwise specified) J Symbol Parameter Definition V Collector To Emitter Breakdown Voltage (BR)CES V Temperature Coeff. of Breakdown Voltage ...

Page 7

PIIPM50P12B004 I27146 Switching Characteristics: Inverter For proper operation the device should be used within the recommended conditions 25°C (unless otherwise specified) J Symbol Parameter Definition Q Total Gate Charge (turn off Gate – Emitter Charge (turn ...

Page 8

PIIPM50P12B004 I27146 Electrical Characteristics: Embedded Driving Board (EDB) communication ports For proper operation the device should be used within the recommended conditions. Vin = 15V, Vin-iso = 5V 55C Symbol Parameter Definition Vin EDB ...

Page 9

PIIPM50P12B004 I27146 AC Electrical Characteristics: Embedded Driving Board (EDB) DSP pins mapping For proper operation the device should be used within the recommended conditions. Vin = 15V, Vin-iso = 5V 55C Symbol Parameter Definition ...

Page 10

PIIPM50P12B004 I27146 Other DSP pins mapping Symbol Signal Definition PWM1 OUT 1 high side IGBT gate drive signal PWM2 OUT 1 low side IGBT gate drive signal PWM3 OUT 2 high side IGBT gate drive signal PWM4 OUT 2 low ...

Page 11

PIIPM50P12B004 I27146 General Description The PI-IPM is a new generation of Intelligent Power Module designed implement itself a complete motor driver system. The device contains all peripherals needed to control a six IGBTs inverter, including voltage, temperature and current completely ...

Page 12

PIIPM50P12B004 I27146 The new package outline is show on page 4, all signal and power pins are clearly listed, note that because of high current spikes on those inputs the DC bus power pins are doubled in size comparing to ...

Page 13

PIIPM50P12B004 I27146 The “2406A” has three different serial interfaces available: SCI, SPI, and CAN bus. In the PI- IPM50P12B004 communication is made through the asynchronous port (SCI) while four other opto-isolated lines can be used for the SPI or for ...

Page 14

PIIPM50P12B004 I27146 acts as a buffer of the partition at 3.30V created down the 5V reference. This 3.30V is used also as reference for the DSP A/D converter. It has to be noted that in the schematic we are using ...

Page 15

PIIPM50P12B004 I27146 sensing pins is detected, this means an over- current detection level of approximately 25%. The delay of this line is around 3 s, fast enough to let the DSP react within the 10 s IGBTs short circuit rating, ...

Page 16

PIIPM50P12B004 I27146 Fig. 1 – Maximum DC collector Current vs. case temperature T = (ºC) C Fig. 3 – Forward SOA T = 25ºC; Tj ≤ 150º (V) CE www.irf.com 06 - Oct Fig. 2 – Power ...

Page 17

PIIPM50P12B004 I27146 Fig. 5 – Typical IGBT Output Characteristics 40º 500 (V) CE Fig. 7 – Typical IGBT Output Characteristics Tj = 125º 500 (V) CE www.irf.com ...

Page 18

PIIPM50P12B004 I27146 Fig. 9 – Typical V vs 40º (V) GE Fig. 11 – Typical 125º (V) GE www.irf.com 06 - Oct GE vs Fig. ...

Page 19

PIIPM50P12B004 I27146 Fig. 13 – Typical Energy Loss vs 125º 250 15V (A) C Fig. 15 – Typical Energy Loss vs 125ºC; ...

Page 20

PIIPM50P12B004 I27146 Fig. 17 – Typical Diode 125º (A) F Fig. 19 – Typical Diode 600V 15V 125ºC dI /dt ( www.irf.com ...

Page 21

PIIPM50P12B004 I27146 Fig. 21 – Typical Diode 125º (A) F Fig. 23 – Typical Gate Charge vs 50A 600 (nC) G www.irf.com 06 - ...

Page 22

PIIPM50P12B004 I27146 Fig. 24 – Normalized Transient Thermal Impedance, Junction-to-copper plate (IGBTs) Fig. 25 – Normalized Transient Impedance, Junction-to-copper plate (FRED diodes) www.irf.com 06 - Oct t1, Rectangular Pulse Duration (sec) t1, Rectangular Pulse Duration (sec) 22 ...

Page 23

PIIPM50P12B004 I27146 www.irf.com 06 - Oct 23 ...

Page 24

PIIPM50P12B004 I27146 www.irf.com 06 - Oct 24 ...

Page 25

PIIPM50P12B004 I27146 Fig. PD1 – Total Dissipated Power vs. f Iout = 7A 530V, T RMS (kHz) SW Fig. PD3 – Total Dissipated Power vs. f Iout = 20A 530V, T RMS DC ...

Page 26

PIIPM50P12B004 I27146 PIIPM family part number identification www.irf.com 06 - Oct 26 ...

Page 27

PIIPM50P12B004 I27146 RS422 and JTAG Connectors top view These connectors do not have any orientation tag; please check their Pin 1 position on Power Module Frame Pins Mapping before inserting mate part. www.irf.com 06 - Oct Top board suggested footprint ...

Page 28

PIIPM50P12B004 I27146 PIIPM50P12B004 case outline and dimensions IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 3252 7105 Data and specifications subject to change without notice. Sales Offices, Agents and Distributors in Major Cities Throughout the World. ...