HS7729KCI01H Renesas Electronics America, HS7729KCI01H Datasheet

Page 1

To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...

Page 2

All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...

Page 3

SuperH™ Family E10A Emulator Additional Document for User’s Manual SH7729 E10A HS7729KCM02HE Renesas Microcomputer Development Environment System SuperH™ Family / SH7700 Series Specific Guide for the SH7729 E10A Emulator Rev.1.0 2003.12 ...

Page 4

Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may ...

Page 5

Section 1 Connecting the Emulator with the User System ............................... 1 1.1 Components of the Emulator ............................................................................................1 1.2 Connecting the E10A Emulator with the User System .....................................................4 1.3 Installing the H-UDI Port Connector on the User System ................................................ 5 1.4 ...

Page 6

ii ...

Page 7

Section 1 Connecting the Emulator with the User System 1.1 Components of the Emulator The SH7729 E10A emulator supports the SH7729 and SH7709A. Table 1.1 lists the components of the emulator. 1 ...

Page 8

... Table 1.1 Components of the Emulator (HS7729KCM01H, HS7729KCM02H, HS7729KCI01H, or HS7729KCI02H) Classi- fication Component Hard- Card emulator ware User system interface cable Ferrite core (connected with the user interface cable) Soft- SH7729 E10A emulator ware setup program, TM SuperH Family E10A Emulator User’s ...

Page 9

Depth: 144.0 mm, Width: 105.0 mm, Mass: 104.0 g The current consumption is 480 mA (max). 2. The length may according to the time for purchasing the product. 3. The EMI is an abbreviation of the Electrical ...

Page 10

... AUD function. Table 1.2 Type Number, AUD Function, and Connector Type Type Number HS7729KCM02H, HS7729KCI02H HS7729KCM01H, HS7729KCI01H The H-UDI port connector has the 36-pin and 14-pin types as described below. Use them according to the purpose of the usage. 1. 36-pin type (with AUD function) The AUD trace function is supported ...

Page 11

Installing the H-UDI Port Connector on the User System Table 1.3 shows the recommended H-UDI port connectors for the emulator. Table 1.3 Recommended H-UDI Port Connectors Connector Type Number 36-pin connector DX10M-36S DX10M-36SE, DX10G1M-36SE 14-pin connector 2514-6002 Note: When ...

Page 12

Pin Input/ *1 No. Signal Output GND 3 AUDATA0 I/O 4 GND 5 AUDATA1 I/O 6 GND 7 AUDATA2 I/O 8 GND 9 AUDATA3 I/O 10 GND *2 11 /AUDSYNC Output 12 GND GND ...

Page 13

Input/ Output* Pin No. Signal 1 TCK Input 2 2* /TRST Input 3 TDO Output 4* 2 /ASEBRKAK Output 5 TMS Input 6 TDI Input 2 7* /RESETP Output 11 Not connected GND 14* ...

Page 14

Recommended Circuit between the H-UDI Port Connector and the MPU 1.5.1 Recommended Circuit (36-Pin Type) Figure 1.4 shows a recommended circuit for connection between the H-UDI port connector (36 pins) and the MPU. Notes not connect anything ...

Page 15

H-UDI port connector (36-pin type GND N. GND AUDATA0 5 6 GND AUDATA1 7 8 GND AUDATA2 9 10 GND AUDATA3 11 12 GND AUDSYNC 13 14 GND N. GND N. GND ...

Page 16

Recommended Circuit (14-Pin Type) Figure 1.5 shows a recommended circuit for connection between the H-UDI port connector (14 pins) and the MPU. Notes not connect anything to the N.C. pins of the H-UDI port connector. 2. Note ...

Page 17

Section 2 Specifications of the SH7729 E10A Emulator’s 2.1 Differences between the SH7729, SH7709A, and the Emulator 1. When the emulator system is initiated, it initializes the general registers and part of the control registers as shown in table 2.1. ...

Page 18

Low-Power States (Sleep, Software Standby, and Module Standby) For low-power consumption, the SH7729 and SH7709A have sleep, software standby, and module standby states. The sleep, software standby, and module standby states are switched using the SLEEP instruction. When the ...

Page 19

When a one-byte memory is read from the command-line window, the stopping time will be about 35 ms. 7. Memory Access during User Program Break The emulator can download the program for the flash memory area (refer to section 6.22, ...

Page 20

... Timeout error will not occur but the memory contents may not be correctly displayed. 13. Loading Sessions Information in [JTAG clock] of the [Configuration] dialog box cannot be recovered by loading sessions. Thus the TCK value will be as follows: When HS7729KCI01H or HS7729KCI02H is used: TCK = 4.125 MHz When HS7729KCM01H or HS7729KCM02H is used: TCK = 3.75 MHz 14. [IO] window Display and modification Do not change values of the User Break Controller because it is used by the emulator ...

Page 21

... Emulator Driver Selection Table 2.4 shows drivers which are selected in the [E10A Driver Details] dialog box. Table 2.4 Type Number and Driver Type Number HS7729KCM01H HS7729KCM02H HS7729KCI01H HS7729KCI02H Driver E10A PC Card Driver 3 E10A PC Card Driver 2 E10A PCI Card Driver 3 E10A PCI Card Driver 2 ...

Page 22

Break Condition Functions In addition to BREAKPOINT functions, the emulator has Break Condition functions. Three types of conditions can be set under Break Condition Table 2.5 lists these conditions of Break Condition. Table 2.5 Types of ...

Page 23

Table 2.6 lists the combinations of conditions that can be set under Break Condition Table 2.6 Dialog Boxes for Setting Break Conditions Type Address Bus Condition Dialog Box (Address) O [Break Condition 1] dialog box O [Break ...

Page 24

... Function Internal trace AUD trace* Realtime trace Non realtime trace Note: When HS7729KCM01H and HS7729KCI01H are used, the AUD function cannot be used. 18 Description Branch instruction trace functions which are built into the chip. This function displays the branch source and branch destination addresses and enables a realtime trace ...

Page 25

... Table 2.8 Type Name and AUD Function Type Name HS7729KCM01H HS7729KCM02H HS7729KCI01H HS7729KCI02H Notes the internal trace of the SH7729 and SH7709A, trace acquisition of the eight latest branch instructions is enabled. In addition, when the user program execution starts, the following one-branch trace is displayed: ...

Page 26

Notes on Using the JTAG Clock (TCK) and AUD Clock (AUDCK) 1. When JTAG clock (TCK) is used, set the JTAG clock (TCK) frequency to lower than the frequency of half of the CPU clock. 2. Set the AUD ...

Page 27

VP_MAP table. However, for addresses out of the range of the VP_MAP table, the address to which a BREAKPOINT is set depends on the SH7729 or SH7709A MMU status during command input. Even when the VP_MAP table ...

Page 28

break address condition is set to the slot instruction after a delayed branch instruction, user program execution cannot be terminated before the slot instruction execution; execution stops before the branch destination instruction break will ...

Page 29

SuperH Family E10A Emulator Additional Document for User's Manual Specific Guide for the SH7729 E10A Emulator Publication Date: Rev.1.00, December 3, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira ...

Page 30

SuperH™ Family E10A Emulator Additional Document for User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10B0066-0100H ...