M52259EVB Freescale Semiconductor, M52259EVB Datasheet - Page 39

• Manufacturer Part Number: M52259EVB
• Description: BOARD EVAL FOR 52259 COLDFIRE V2
• Manufacturer: Freescale Semiconductor
• Series: ColdFire®r
• Type: MCUr

Specifications of M52259EVB

• Contents: Board, Cables, Documentation, DVD, Flash Drive and Power Supply
• Processor To Be Evaluated: MCF52259
• Data Bus Width: 32 bit
• Interface Type: RS-232, Ethernet, USB
• Silicon Manufacturer: Freescale
• Core Architecture: Coldfire
• Core Sub-architecture: Coldfire V2
• Silicon Core Number: MCF52
• Silicon Family Name: MCF5225x
• Peak Reflow Compatible (260 C): Yes
• Rohs Compliant: Yes
• For Use With/related Products: MCF52259
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Electrical Characteristics
2.16
Figure 14
closed/open. When S1/S2 are closed & S3 is open, one input of the sample and hold circuit moves to (V
the other charges to the analog input voltage. When the switches are flipped, the charge on C1 and C2 are averaged via S3, with
the result that a single-ended analog input is switched to a differential voltage centered about (V
switch on every cycle of the ADC clock (open one-half ADC clock, closed one-half ADC clock). There are additional
capacitances associated with the analog input pad, routing, etc., but these do not filter into the S/H output voltage, as S1 provides
isolation during the charge-sharing phase. One aspect of this circuit is that there is an on-going input current, which is a function
of the analog input voltage, V
39
1
2
3
4
5
6
7
All measurements are preliminary pending full characterization, and made at V
INL measured from V
LSB = Least Significant Bit
INL measured from V
Includes power-up of ADC and V
ADC clock cycles
Current that can be injected or sourced from an unselected ADC signal input without impacting the performance of the ADC
SINAD
ENOB
Name
SFDR
SNR
THD
1.
2.
3.
4.
5.
Parasitic capacitance due to package, pin-to-pin and pin-to-package base coupling; 1.8pF
Parasitic capacitance due to the chip bond pad, ESD protection devices and signal routing; 2.04pF
Equivalent resistance for the channel select mux; 100 s
Sampling capacitor at the sample and hold circuit. Capacitor C1 is normally disconnected from the input and is only
connected to it at sampling time; 1.4pF
Equivalent input impedance, when the input is selected =
shows the ADC input circuit during sample and hold. S1 and S2 are always open/closed at the same time that S3 is
Analog Input
Equivalent Circuit for ADC Inputs
Signal-to-noise ratio
Total harmonic distortion
Spurious free dynamic range
Signal-to-noise plus distortion
Effective number of bits
1
IN
IN
= V
= 0.1V
REF
REFL
2
REFH
Characteristic
and the ADC clock frequency.
to V
REF
Figure 14. Equivalent Circuit for A/D Loading
to V
IN
Table 25. ADC Parameters
MCF52259 ColdFire Microcontroller, Rev. 4
= V
IN
REFH
= 0.9V
125W ESD Resistor
REFH
(V
REFH
3
- V
REFL
)/ 2
(ADC Clock Rate)  (1.410
8pF noise damping capacitor
S1
1
(continued)
S2
Min
9.1
—
—
—
—
1
DD
4
= 3.3V, V
S3
67 to 70.3
61 to 63.9
62 to 66
Typical
10.6
75
C2
C1
-12
REFH
)
REFH
S/H
= 3.3V, and V
Freescale Semiconductor
-V
C1 = C2 = 1pF
Max
REFH
REFL
—
—
—
—
—
)/2. The switches
-V
REFL
REFL
)/2, while
Unit
= ground
Bits
dB
dB
dB
dB