EDK2329 Renesas Electronics America, EDK2329 Datasheet - Page 10

• Manufacturer Part Number: EDK2329
• Description: DEV EVALUATION KIT H8S/2329
• Manufacturer: Renesas Electronics America
• Series: H8®r
• Type: MCUr

Specifications of EDK2329

• Contents: 2G (Second-generation) Evaluation Board, HEW debugger support, Cable and CD-ROM
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With/related Products: H8S/2329
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant

5.2. U
CJ5 is used to set the operating mode of the microcontroller.
These jumpers must be fitted at all times to ensure correct operation of the EDK.
The default settings indicated in bold text place the microcontroller into Mode 6, i.e. advanced expanded mode with on-chip
ROM enabled.
Note : CJ5-D is not connected to any signal on the EDK as the H8S/2329 does not utilise a MD3 pin.
5.3.
The EDK options provide access to commonly used features of the EDK range.
These jumpers must be fitted at all times to ensure correct operation of the EDK.
*
*
protect function.
The following table lists the connections to each jumper pin.
1
2
See section 5.5
Please note function of CJ4-B is different to the majority of EDKs where an FWE pin enables and disables the flash write
EDK O
SER
CJ 4-A
Default 2-3
CJ 4-B
Default 2-3
CJ 4-C
Default 2-3
CJ 4-D
Default 1-2
1
2
3
4
5
6
7
8
9
10
11
12
Pin
M
Jumper
ODE
PTIONS
CJ 5-A
Default 2-3
CJ 5-B
Default 1-2
CJ 5-C
Default 1-2
CJ 5-D
Default 1-2
UVCC
RXDISn
No Connection
UVCC
UPM
No Connection
PG4
CSn
No Connection
No Connection
No Connection
No Connection
Jumper
S
Net Name
ETTINGS
– CJ4
Serial Receive
Source
User
Programming
Mode *
CSn
No Connection
Function
User Mode Setting Bit 0
User Mode Setting Bit 1
User Mode Setting Bit 2
User Mode Setting Bit 3
– CJ5
2
T
ABLE
T
Microcontroller Supply Voltage
Disable Flash Header functions. Pulled low. (Enables RX232)
No Connection
Microcontroller Supply Voltage
CPLD Controlled option to set Flash Write (FW). Pulled low.
E10A Enable / Disable Signal.
No Connection
Microcontroller CSn(0) signal
SRAM CSn signal
No Connection
No Connection
No Connection
No Connection
ABLE
Function
5-2: B
5-1: U
Disables the RS232 receive signal
to enable the use of the Flash
Programming Header
Enables E10A interface.
SRAM enabled when H8S/2329
CSn(0) signal is asserted
No Connection
OARD
SER
M
O
ODE
PTION
Setting 1-2
: J
: J
UMPER
MD0 pulled High
MD1 pulled High
MD2 pulled High
MD3 pulled High
UMPER
S
ETTINGS
S
Setting 1-2
ETTINGS
Description
(D
(D
EFAULT SETTINGS IN BOLD
EFAULT SETTINGS IN BOLD
Enables the RS232 receive signal.
The Flash Programming Header *
must not be used in this state.
Disables E10A Interface.
SRAM Disabled
No Connection
MD0 pulled Low
MD1 pulled Low
MD2 pulled Low
MD3 pulled Low
Setting 2-3
Setting 2-3
)
)
1
10