C8051F996DK Silicon Laboratories Inc, C8051F996DK Datasheet - Page 16

• Manufacturer Part Number: C8051F996DK
• Description: KIT DEV FOR C8051F996
• Manufacturer: Silicon Laboratories Inc
• Type: MCUr

Specifications of C8051F996DK

• Contents: Board, Batteries, Cables, CDs, Debug Adapter, Documentation, Power Adapter
• Processor To Be Evaluated: C8051F996
• Processor Series: C8051F98x
• Interface Type: USB
• Operating Supply Voltage: 3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: C8051F996
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1963

C8051F996-DK
7.5. Switches and LEDs (J1, J5, J8, J15, J16, SW1, SW2, SW3)
Three push-button switches are provided on the target board. Switch SW1 (RESET) is connected to the reset pin
of the C8051F996. Pressing SW1 puts the device into its hardware-reset state. Switches SW2 (P0.2) and SW3
(P0.3) are connected to the C8051F996’s general purpose I/O (GPIO) pins through headers. Pressing SW2 or
SW3 generates a logic low signal on the port pin. Remove the shorting block from the header (J8) to disconnect the
switches from the port pins. The port pin signal is also routed to pins on the J2 and P1 I/O connectors. See Table 2
for the port pins and headers corresponding to each switch.
Two touch sensitive (contactless) switches are provided on the target board. The operation of these switches
require appropriate firmware running on the C8051F996 MCU that can sense the state of the switch.
Four power LEDs are provided on the target board to serve as indicators. The 3.3 V regulator has a red LED used
to indicate the presence of power at the output of the regulator. A red USB Power LED turns on when a USB cable
is plugged into the USB connector P3. One power LED is also added to each of the two primary supply nets
powering the MCU (VDD and PWR). The PWR net is before the power measurement header and the VDD net is
after the power measurement header. The LEDs connected to the supply nets may be disabled by removing the
shorting blocks from J1 and J5.
Two LEDs are connected to GPIO pins P1.5 and P1.3 for use by application software. See Table 2 for the port pins
and headers corresponding to each LED.
A potentiometer (R15) is also provided on the target board for generating analog signals. Place a shorting block on
J16 to connect the wiper to P0.6/CNVSTR. The header J15 allows the negative terminal of the potentiometer to be
tied to GND or to P1.4. When tied to GND, the potentiometer is always enabled and will draw a measurable
amount of supply current. When tied to P1.4, it only draws current when P1.4 is driving a logic 0 and draws no
current when P1.4 is driving a logic 1.
16
P1.0 (Touch Sense Switch)
P1.1 (Touch Sense Switch)
Red LED (+3 VD Power)
Red LED (USB Power)
Potentiometer (R15)
Yellow LED (P1.3)
Red LED (PWR)
Red LED (P1.5)
Red LED (VDD)
Description
SW1
SW2
SW3
Table 2. Target Board I/O Descriptions
+3 VD Regulator Output
Rev. 0.1
PWR Supply Net
VDD Supply Net
USB VBUS
P0.6/P1.4
Reset
P0.2
P0.3
P1.0
P1.1
P1.5
P1.3
I/O
Header(s)
J15, J16
J8[5–6]
J8[7–8]
J8[1–2]
J8[3–4]
none
none
none
none
none
J5
J1