STEVAL-MKI006V1 STMicroelectronics, STEVAL-MKI006V1 Datasheet - Page 32

• Manufacturer Part Number: STEVAL-MKI006V1
• Description: BOARD EVALUATION LIS302DL
• Manufacturer: STMicroelectronics
• Series: MEMSr

Specifications of STEVAL-MKI006V1

• Design Resources: STEVAL-MKI006V1 Gerber Files STEVAL-MKI006V1 Schematic STEVAL-MKI006V1 Bill of Materials
• Sensor Type: Accelerometer, 3 Axis
• Sensing Range: ±2.3g, 9.2g
• Interface: SPI, USB
• Sensitivity: 18 ~ 72 mg/Digit
• Voltage - Supply: 5V, USB
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: LIS302DL
• Acceleration: 2 g, 8 g
• Sensing Axis: Triple Axis
• Output Type: Digital
• Interface Type: USB
• Silicon Manufacturer: ST Micro
• Silicon Core Number: LIS302DL
• Kit Application Type: Sensing - Motion / Vibration / Shock
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-6229

Register description
7.13
7.14
32/42
FF_WU_DURATION_1 (33h)
Table 37.
Table 38.
Duration register for Free-Fall/Wake-Up interrupt 1. Duration step and maximum value
depend on the ODR chosen. Step 2.5 msec, from 0 to 637.5 msec if ODR=400Hz, else step
10 msec, from 0 to 2.55 sec when ODR=100Hz. The counter used to implement duration
function is blocked when LIR=1 in configuration register and the interrupt event is verified
FF_WU_CFG_2 (34h)
Table 39.
Table 40.
AOI
LIR
ZHIE
ZLIE
YHIE
YLIE
XHIE
XLIE
AOI
D7
D7-D0
FF_WU_DURATION_1 (33h) register
FF_WU_DURATION_1 (33h) register description
FF_WU_CFG_2 (34h) register
FF_WU_CFG_2 (34h) register description
And/or combination of Interrupt events. Default value: 0
(0: OR combination of interrupt events; 1: AND combination of interrupt events)
Latch interrupt request into FF_WU_SRC reg with the FF_WU_SRC reg cleared by
reading FF_WU_SRC_2 reg. Default value: 0
(0: interrupt request not latched; 1: interrupt request latched)
Enable interrupt generation on Z high event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value higher than preset threshold)
Enable interrupt generation on Z low event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value lower than preset threshold)
Enable interrupt generation on Y high event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value higher than preset threshold)
Enable interrupt generation on Y low event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value lower than preset threshold)
Enable interrupt generation on X high event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value higher than preset threshold)
Enable interrupt generation on X low event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value lower than preset threshold)
LIR
D6
Duration value. Default value: 0000 0000
ZHIE
D5
ZLIE
D4
YHIE
D3
YLIE
D2
XHIE
D1
LIS302DL
XLIE
D0