STEVAL-MKI029V1 STMicroelectronics, STEVAL-MKI029V1 Datasheet - Page 56
![BOARD DEMO STM8S207R6/LIS331DLH](/photos/28/40/284023/steval-mki029v1_sml.jpg)
STEVAL-MKI029V1
Manufacturer Part Number
STEVAL-MKI029V1
Description
BOARD DEMO STM8S207R6/LIS331DLH
Manufacturer
STMicroelectronics
Series
MEMSr
Datasheets
1.STEVAL-MKI009V1.pdf
(42 pages)
2.STEVAL-MKI022V1.pdf
(38 pages)
3.STEVAL-MKI030V1.pdf
(105 pages)
4.STEVAL-MKI029V1.pdf
(4 pages)
Specifications of STEVAL-MKI029V1
Sensor Type
Accelerometer, 3 Axis
Sensing Range
±2g, 4g, 8g
Interface
I²C, SCI
Sensitivity
3.9mg/digit, 2mg/digit, 1mg/digit
Voltage - Supply
4.5V
Embedded
Yes, MCU, 8-Bit
Utilized Ic / Part
LIS331DLH, STM8S207R6T6
Sensing Axis
Double Axis
Operating Voltage
5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-8851
Electrical characteristics
56/105
Table 16.
1. Data based on characterization results, not tested in production.
2. All power (V
3. I/O pins used simultaneously for high current source/sink must be uniformly spaced around the package
4. I
5. Negative injection disturbs the analog performance of the device. See note in
6. When several inputs are submitted to a current injection, the maximum
Table 17.
I
I
INJ(PIN)
external supply.
between the V
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
there is no positive injection current, and the corresponding V
characteristics on page
positive and negative injected currents (instantaneous values). These results are based on
characterization with
INJ(PIN)
Symbol
INJ(PIN)
Symbol
I
I
I
VDD
VSS
I
T
IO
IO
STG
T
(4)(5)
J
must never be exceeded. This is implicitly insured if V
(4)
Current characteristics
Thermal characteristics
DD
DDIO
, V
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Total output current sourced (sum of all I/O and control pins)
for devices with two V
Total output current sourced (sum of all I/O and control pins)
for devices with one V
Total output current sunk (sum of all I/O and control pins) for
devices with two V
Total output current sunk (sum of all I/O and control pins) for
devices with one V
Injected current on NRST pin
Injected current on OSCIN pin
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DDIO
/V
SSIO
, V
I
INJ(PIN)
84.
IN
DDA
>V
pins.
DD
) and ground (V
Maximum junction temperature
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Storage temperature range
Doc ID 14733 Rev 11
SSIO
DD
SSIO
SS
DDIO
power lines (source)
DDIO
Ratings
pins
ground lines (sink)
pin
SS
Ratings
, V
(3)
pins
pin
(3)
SSIO
(3)
(3)
(6)
, V
SSA
) pins must always be connected to the
IN
IN
maximum must always be respected
maximum is respected. If V
(2)
(2)
I
IN
INJ(PIN)
STM8S207xx, STM8S208xx
<V
INJ(PIN)
(6)
SS
Section 10.3.10: 10-bit ADC
. For true open-drain pads,
is the absolute sum of the
-65 to 150
value. A positive
Value
150
Max.
±20
200
100
160
60
60
20
20
80
±4
±4
±4
IN
(1)
maximum
Unit
Unit
°C
mA