MAX110EVC32-DIP Maxim Integrated Products, MAX110EVC32-DIP Datasheet - Page 2

• Manufacturer Part Number: MAX110EVC32-DIP
• Description: EVAL KIT FOR MAX110
• Manufacturer: Maxim Integrated Products

Specifications of MAX110EVC32-DIP

• Number Of Adc's: 1
• Number Of Bits: 14
• Sampling Rate (per Second): 50
• Data Interface: Serial
• Inputs Per Adc: 2 Differential
• Input Range: ±VREF
• Power (typ) @ Conditions: 4.35mW @ 50SPS
• Voltage Supply Source: Single Supply
• Operating Temperature: 0°C ~ 70°C
• Utilized Ic / Part: MAX110, MAX111
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MAX110 Evaluation System/Evaluation Kit
________EV System Component List
2
DESIGNATION QTY
QTY
C1–C5, C7–10
____________EV Kit Component List
1
1
R6, R7, R8
J1, J4, J5
J2, J3, J9
_______________________________________________________________________________________
C11–C15
C17, C18
C6–C16,
R1-R4
J7, J8
None
None
None
None
None
None
R10
R11
R12
U1
U2
U3
U4
H1
R5
R9
J6
MAX110 evaluation kit (MAX110EVKIT-DIP)
80C32 µC module (80C32MODULE-DIP)
9
5
4
4
1
3
1
1
1
0
1
1
1
1
3
2
0
0
1
1
5
1
1
1
4
0.1µF ceramic capacitors
10µF, 16V radial tantalum capacitors
1µF ceramic capacitors
1kΩ, 5% resistors
10kΩ, 8-pin SIP resistor, pin 1 common
100Ω, 5% resistors
200Ω multi-turn potentiometer
2.43kΩ, 1% resistor
10kΩ, 1% resistor
Leave this site empty
MAX110CPE
ICL7660CPA
1.024MHz crystal oscillator module
MAX873CPA
3-pin headers
2-pin headers
Leave these sites empty
Unused reference designator
10-pin header
Female data connector
Shunts
14-pin socket for U3
16-pin socket for U1
4.5" x 3" PC board
Rubber feet
DESCRIPTION
DESCRIPTION
This section applies only to the use of the MAX110 EV
kit operating with the Maxim 80C32 module.
1) Copy the files from the distribution disk to your hard
2) Carefully connect the boards together by aligning
3) Connect a 9V to 15V DC power source to the 80C32
4) Connect a cable from the computer’s serial port to
5) Start the MAX110 software on the IBM PC by
6) The program will ask to which serial port the 80C32
7) The MAX110 program will be in terminal emulation
8) To download and run the RAM resident code on the
9) When the RAM resident program has been suc-
___MAX110 EV System Quick Start
disk or to blank floppy disks. The MAX110 EV kit
software should be in its own directory. The neces-
sary files are in the root directory of the
distribution disk, and the source code is in the
SOURCE subdirectory. The SOURCE subdirectory
is not required to operate the EV kit.
the 40-pin header of the MAX110 EV kit with the 40-
pin connector of the 80C32 module. Gently press
them together. The two boards should be flush
against one another.
module. The terminal block is located next to the
on/off switch, in the upper right corner of the 80C32
module. Observe the polarity marked on the board.
the 80C32 module. If using a 9-pin serial port, use a
straight-through 9-pin female-to-male cable. If the
only available serial port uses a 25-pin connector, a
standard 25-pin to 9-pin adapter will be required.
setting the current directory to match the directory
that contains the Maxim programs, and then type
the program name, “MAX110”. Do not turn off or
disconnect the 80C32 module while the program is
running; if you do, you will have to restart the pro-
gram.
module is connected. Press the space bar until the
correct port is highlighted, and then press ENTER.
mode. Turn on the power for the 80C32 module.
The 80C32 module will display its logon banner and
test its RAM.
80C32 module, press ALT+L (i.e. hold down the
ALT key as you strike the L key). The program
prompts you for the file name. Press the ENTER key
to download and run the file 110CODE.MAX on the
80C32 module.
cessfully downloaded, press ALT+C to switch to the
Control Panel screen. A bank of software “switches”
controls the MAX110. Two double-needle bar
graphs display the MAX110’s twin channels. The