MAX1292EVKIT Maxim Integrated Products, MAX1292EVKIT Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX1292EVKIT
Manufacturer Part Number
MAX1292EVKIT
Description
EVALUATION KIT FOR MAX1292
Manufacturer
Maxim Integrated Products
Specifications of MAX1292EVKIT
Number Of Adc's
1
Number Of Bits
12
Sampling Rate (per Second)
400k
Data Interface
Parallel
Inputs Per Adc
4 Single Ended
Input Range
±VREF/2
Power (typ) @ Conditions
9.5mW @ 400kSPS
Voltage Supply Source
Single Supply
Operating Temperature
0°C ~ 70°C
Utilized Ic / Part
MAX1292, MAX1293
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
400ksps, +5V, 8-/4-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
8
MAX1290
_______________________________________________________________________________________
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
2
3
4
5
6
7
8
9
PIN
MAX1292
10
11
12
13
14
—
—
—
—
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
REFADJ
D3/D11
D2/D10
V
NAME
D1/D9
D0/D8
HBEN
COM
GND
CH7
CH6
CH5
CH4
CH3
CH2
CH1
CH0
LOGIC
CLK
REF
V
INT
WR
RD
D7
D6
D5
D4
CS
DD
High Byte Enable. Used to multiplex the 12-bit conversion result.
1: Four MSBs are multiplexed on the data bus.
0: Eight LSBs are available on the data bus.
Three-State Digital I/O Line (D7)
Three-State Digital I/O Line (D6)
Three-State Digital I/O Line (D5)
Three-State Digital I/O Line (D4)
Three-State Digital I/O Line (D3, HBEN = 0; D11, HBEN = 1)
Three-State Digital I/O Line (D2, HBEN = 0; D10, HBEN = 1)
Three-State Digital I/O Line (D1, HBEN = 0; D9, HBEN = 1)
Three-State Digital I/O Line (D0, HBEN = 0; D8, HBEN = 1)
INT goes low when the conversion is complete and the output data is ready.
Active-Low Read Select. If CS is low, a falling edge on RD enables the read operation on the
data bus.
Active-Low Write Select. When CS is low in internal acquisition mode, a rising edge on WR
latches in configuration data and starts an acquisition plus a conversion cycle. When CS is
low in external acquisition mode, the first rising edge on WR ends acquisition and starts a
conversion.
Clock Input. In external clock mode, drive CLK with a TTL/CMOS-compatible
clock. In internal clock mode, connect this pin to either V
Active-Low Chip Select. When CS is high, digital outputs (INT, D7–D0) are high impedance.
Analog Input Channel 7
Analog Input Channel 6
Analog Input Channel 5
Analog Input Channel 4
Analog Input Channel 3
Analog Input Channel 2
Analog Input Channel 1
Analog Input Channel 0
Ground Reference for Analog Inputs. Sets zero-code voltage in single-ended mode and
must be stable to ±0.5 LSB during conversion.
Analog and Digital Ground
Bandgap Reference Output/Bandgap Reference Buffer Input. Bypass to GND with a 0.01µF
capacitor. When using an external reference, connect REFADJ to V
bandgap reference.
Bandgap Reference Buffer Output/External Reference Input. Add a 4.7µF capacitor to GND
when using the internal reference.
Analog +5V Power Supply. Bypass with a 0.1µF capacitor to GND.
Digital Power Supply. V
from +2.7V to V
DD
+ 300mV.
LOGIC
powers the digital outputs of the data converter and can range
FUNCTION
DD
or GND.
Pin Description
DD
to disable the internal