MAX1292EVKIT Maxim Integrated Products, MAX1292EVKIT Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX1292EVKIT
Manufacturer Part Number
MAX1292EVKIT
Description
EVALUATION KIT FOR MAX1292
Manufacturer
Maxim Integrated Products
Specifications of MAX1292EVKIT
Number Of Adc's
1
Number Of Bits
12
Sampling Rate (per Second)
400k
Data Interface
Parallel
Inputs Per Adc
4 Single Ended
Input Range
±VREF/2
Power (typ) @ Conditions
9.5mW @ 400kSPS
Voltage Supply Source
Single Supply
Operating Temperature
0°C ~ 70°C
Utilized Ic / Part
MAX1292, MAX1293
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
conversion. The sampling interval occurs at the end of
the acquisition interval. The ACQMOD (acquisition
mode) bit in the input control byte (Table 1) offers two
options for acquiring the signal: an internal and an
external acquisition. The conversion period lasts for 13
clock cycles in either the internal or external clock or
acquisition mode. Writing a new control byte during a
conversion cycle aborts the conversion and starts a
new acquisition interval.
Select internal acquisition by writing the control byte
with the ACQMOD bit cleared (ACQMOD = 0). This
causes the write pulse to initiate an acquisition interval
whose duration is internally timed. Conversion starts
when this acquisition interval (three external clock
cycles or approximately 1µs in internal clock mode)
ends (Figure 4). Note that, when the internal acquisition
is combined with the internal clock, the aperture jitter
can be as high as 200ps. Internal clock users wishing
to achieve the 50ps jitter specification should always
use external acquisition mode.
Use external acquisition mode for precise control of the
sampling aperture and/or dependent control of acquisi-
tion and conversion times. The user controls acquisition
and start-of-conversion with two separate write pulses.
Table 1. Control Byte Functional Description
D2, D1, D0
D7, D6
BIT
D5
D4
D3
with +2.5V Reference and Parallel Interface
ACQMOD
PD1, PD0
SGL/DIF
UNI/BIP
A2, A1, A0
NAME
______________________________________________________________________________________
400ksps, +5V, 8-/4-Channel, 12-Bit ADCs
PD1 and PD0 select the various clock and power-down modes.
ACQMOD = 0: Internal Acquisition Mode
ACQMOD = 1: External Acquisition Mode
SGL/DIF = 0: Pseudo-Differential Analog Input Mode
SGL/DIF = 1: Single-Ended Analog Input Mode
In single-ended mode, input signals are referred to COM. In pseudo-differential mode, the voltage
difference between two channels is measured (Tables 2, 3).
UNI/BIP = 0: Bipolar Mode
UNI/BIP = 1: Unipolar Mode
In unipolar mode, an analog input signal from 0 to V
signal can range from -V
Address bits A2, A1, A0 select which of the 8/4 (MAX1290/MAX1292) channels is to be converted
(Tables 3, 4).
0
0
1
1
External Acquisition
Internal Acquisition
0
1
0
1
Full Power-Down Mode. Clock mode is unaffected.
Standby Power-Down Mode. Clock mode is unaffected.
Normal Operation Mode. Internal clock mode is selected.
Normal Operation Mode. External clock mode is selected.
REF
/2 to +V
REF
The first pulse, written with ACQMOD = 1, starts an
acquisition interval of indeterminate length. The second
write pulse, written with ACQMOD = 0 (all other bits in
the control byte are unchanged), terminates acquisition
and starts conversion on WR rising edge (Figure 5).
The address bits for the input multiplexer must have the
same values on the first and second write pulses.
Power-down mode bits (PD0, PD1) can assume new
values on the second write pulse (see the Power-Down
Modes section). Changing other bits in the control byte
corrupts the conversion.
A standard interrupt signal, INT, is provided to allow the
MAX1290/MAX1292 to flag the microprocessor when
the conversion has ended and a valid result is avail-
able. INT goes low when the conversion is complete
and the output data is ready (Figures 4 and 5). INT
returns high on the first read cycle or if a new control
byte is written.
The MAX1290/MAX1292 operate with an internal or
external clock. Control bits D6 and D7 select either
internal or external clock mode. The part retains the
last-requested clock mode if a power-down mode is
selected in the current input word. For both internal and
external clock mode, internal or external acquisition
/2.
FUNCTION
REF
can be converted; in bipolar mode, the
Reading a Conversion
Selecting Clock Mode
11