EVAL-AD7671CBZ Analog Devices Inc, EVAL-AD7671CBZ Datasheet - Page 19

• Manufacturer Part Number: EVAL-AD7671CBZ
• Description: BOARD EVALUATION FOR AD7671
• Manufacturer: Analog Devices Inc
• Series: PulSAR®r

Specifications of EVAL-AD7671CBZ

• Number Of Adc's: 1
• Number Of Bits: 16
• Sampling Rate (per Second): 1M
• Data Interface: Serial, Parallel
• Inputs Per Adc: 4 Single Ended
• Input Range: ±4 REF
• Power (typ) @ Conditions: 112mW @ 1MSPS
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: AD7671
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

the AD7671 provides error correction circuitry that can correct
for an improper bit decision made during the first half of the
conversion phase. For this reason, it is recommended that when
an external clock is being provided, it is a discontinuous clock
that is toggling only when BUSY is LOW or, more importantly,
that does not transition during the latter half of BUSY HIGH.
External Discontinuous Clock Data Read after Conversion
Though the maximum throughput cannot be achieved using this
mode, it is the most recommended of the serial slave modes.
Figure 19 shows the detailed timing diagrams of this method.
After a conversion is complete, indicated by BUSY returning LOW,
the result of this conversion can be read while both CS and RD
are LOW. The data is shifted out, MSB first, with 16 clock
pulses and is valid on both the rising and falling edge of the clock.
Among the advantages of this method, the conversion perfor-
mance is not degraded because there are no voltage transients
on the digital interface during the conversion process.
Another advantage is to be able to read the data at any speed up to
40 MHz, which accommodates both slow digital host interface
and the fastest serial reading.
Finally, in this mode only, the AD7671 provides a “daisy-chain”
feature using the RDC/SDIN input pin for cascading multiple
converters together. This feature is useful for reducing component
count and wiring connections when desired as, for instance, in
isolated multiconverter applications.
An example of the concatenation of two devices is shown in Fig-
ure 20. Simultaneous sampling is possible by using a common
CNVST signal. It should be noted that the RDC/SDIN input is
latched on the opposite edge of SCLK of the one used to shift out
the data on SDOUT. Therefore, the MSB of the “upstream”
converter just follows the LSB of the “downstream” converter
on the next SCLK cycle.
REV. B
SDOUT
CS, RD
BUSY
SCLK
SDIN
Figure 19. Slave Serial Data Timing for Reading (Read after Convert)
t
t
31
16
t
33
X
t
36
1
t
35
D15
X15
t
37
t
34
EXT/INT = 1
2
D14
X14
t
32
3
X13
D13
–19–
External Clock Data Read during Conversion
Figure 21 shows the detailed timing diagrams of this method.
During a conversion, while both CS and RD are LOW, the result
of the previous conversion can be read. The data is shifted out,
MSB first, with 16 clock pulses and is valid on both the rising and
the falling edge of the clock. The 16 bits have to be read before the
current conversion is complete. If that is not done, RDERROR
is pulsed HIGH and can be used to interrupt the host interface
to prevent incomplete data reading. There is no daisy-chain feature
in this mode, and RDC/SDIN input should always be tied either
HIGH or LOW.
Figure 20. Two AD7671s in a Daisy-Chain Configuration
INVSCLK = 0
CNVST IN
SCLK IN
14
CS IN
RDC/SDIN
(UPSTREAM)
AD7671
15
BUSY
#2
X1
D1
SDOUT
CNVST
SCLK
16
CS
RD = 0
D0
X0
17
X15
Y15
RDC/SDIN
18
(DOWNSTREAM)
AD7671
X14
Y14
BUSY
#1
SDOUT
CNVST
SCLK
AD7671
CS
BUSY
OUT
DATA
OUT