EVAL-AD7864-2CB Analog Devices Inc, EVAL-AD7864-2CB Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
EVAL-AD7864-2CB
Manufacturer Part Number
EVAL-AD7864-2CB
Description
EVAL BOARD FOR AD7864 DATA SYS
Manufacturer
Analog Devices Inc
Datasheet
1.AD7864ASZ-1.pdf
(28 pages)
Specifications of EVAL-AD7864-2CB
Rohs Status
RoHS non-compliant
Number Of Adc's
1
Number Of Bits
12
Sampling Rate (per Second)
520k
Data Interface
Parallel
Inputs Per Adc
4 Differential
Input Range
0 ~ 5 V
Power (typ) @ Conditions
90mW @ 520kSPS
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD7864-2
Lead Free Status / Rohs Status
Not Compliant
Other names
Q1722474
TIMING CHARACTERISTICS
V
Table 2.
Parameter
t
t
t
t
t
t
t
READ OPERATION
WRITE OPERATION
1
2
3
4
5
CONV
ACQ
BUSY
WAKE-UP
WAKE-UP
1
2
Sample tested at initial release to ensure compliance. All input signals are measured with tr = tf = 1 ns (10% to 90% of 5 V) and timed from a voltage level of 1.6 V.
See Figure 9, Figure 10,and Figure 11.
Refer to the Standby Mode Operation section. The maximum specification of 6 ms is valid when using a 0.1 μF decoupling capacitor on the V
Measured with the load circuit of Figure 2 and defined as the time required for an output to cross 0.8 V or 2.4 V.
These times are derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit shown in Figure 2. The measured number is
then extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the timing characteristics are the
true bus relinquish times of the part, and as such, are independent of external bus loading capacitances.
t
t
t
t
t
t
t
t
t
t
DRIVE
3
4
5
6
7
8
9
10
11
12
t
t
t
t
t
4
5
13
14
15
16
17
= 5 V± 5%, AGND = DGND = 0 V, V
—External V
—Internal V
REF
REF
3
A, B Versions
1.65
13
2.6
0.34
No. of channels ×
(t
2
6
35
70
0
0
35
40
35
40
5
30
10
75
180
70
15
0
20
0
0
5
5
CONV
+ t
9
) − t
9
Figure 2. Load Circuit for Access Time and Bus Relinquish Time
REF
= internal, clock = internal; all specifications T
OUTPUT
TO
Unit
μs max
Clock cycles
μs max
μs max
μs max
μs max
ms max
ns min
ns max
ns min
ns min
ns min
ns min
ns max
ns max
ns min
ns max
ns min
ns min
ns max
ns max
ns max
ns min
ns min
ns min
ns min
ns min
ns min
50pF
Rev. D | Page 5 of 28
1.6mA
400µA
Test Conditions/Comments
Conversion time, internal clock
Conversion time, external clock
CLKIN = 5 MHz
Acquisition time
Selected number of channels multiplied by (t
width)— EOC pulse width
STBY rising edge to CONVST rising edge
STBY rising edge to CONVST rising edge
CONVST pulse width
CONVST rising edge to BUSY rising edge
CS to RD setup time
CS to RD hold time
Read pulse width, V
Read pulse width, V
Data access time after falling edge of RD , V
Data access time after falling edge of RD , V
Bus relinquish time after rising edge of RD
Time between consecutive reads
EOC pulse width
RD rising edge to FRSTDATA edge (rising or falling)
EOC falling edge to FRSTDATA falling delay
EOC to RD delay
WR pulse width
CS to WR setup time
WR to CS hold time
Input data setup time of rising edge of WR
Input data hold time
1.6V
DRIVE
DRIVE
MIN
= 5 V
= 3 V
to T
MAX
, unless otherwise noted.
DRIVE
DRIVE
REF
CONV
pin.
= 5 V
= 3 V
+ EOC pulse
AD7864
1, 2