MAX9675EVKIT+ Maxim Integrated Products, MAX9675EVKIT+ Datasheet - Page 3

• Manufacturer Part Number: MAX9675EVKIT+
• Description: KIT EVAL FOR MAX9675
• Manufacturer: Maxim Integrated Products

Specifications of MAX9675EVKIT+

• Main Purpose: Interface, Crosspoint Switch/Multiplexer
• Embedded: No
• Utilized Ic / Part: MAX9675
• Primary Attributes: 16 x 16 Video Crosspoint Switch
• Secondary Attributes: Graphical User Interface, USB Interface
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8) Connect the ground terminal of the -5V analog
9) Connect the negative terminal of the -5V analog
10) Verify that all jumpers are in their default positions,
11) Connect the output of the video signal generator to
12) Connect the OUT00 connector of the MAX9675 EV
13) Turn on all power supplies.
14) Turn on the video signal generator.
15) Connect the USB cable from the PC to the EV kit
Table 1. Jumper Settings (JU1–JU4, JU6–JU13)
* Default position.
power supply to pin 2 of the J2 connector.
power supply to pin 3 of the J2 connector.
as shown in Table 1.
the IN00 connector on the MAX9675 EV kit.
kit to the input of the video measurement equipment.
board. A New Hardware Found window pops up
when installing the USB driver for the first time. If you
do not see a window that is similar to the one
described above after 30 seconds, remove the USB
cable from the board and reconnect it. Administrator
privileges are required to install the USB device driver
on Windows.
JUMPER
JU1–JU4
JU10
JU11
JU12
JU13
JU6
JU7
JU8
JU9
_______________________________________________________________________________________
SHUNT POSITION
2-3*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2
2-3
2-3
2-3
2-3
2-3
2-3
2-3
2-3
Connects the address pin to VDD
Connects the address pin to ground
MISO signal connected to on-board microcontroller
Connect external MISO signal to pin 1 of the J16 connector
MOSI signal connected to on-board microcontroller
Connect external MOSI signal to pin 3 of the J16 connector
SCLK signal connected to on-board microcontroller
Connect external SCLK signal to pin 5 of the J16 connector
CE signal connected to on-board microcontroller
Connect external CE signal to pin 7 of the J16 connector
AOUT signal connected to on-board microcontroller
Connect external AOUT signal to pin 9 of the J16 connector
MODE signal connected to on-board microcontroller
Connect external MODE signal to pin 11 of the J16 connector
RESET signal connected to on-board microcontroller
Connect external RESET signal to pin 13 of the J16 connector
UPDATE signal connected to on-board microcontroller
Connect external UPDATE signal to pin 15 of the J16 connector
MAX9675 Evaluation Kit
16) Follow the directions of the Add New Hardware
17) Start the MAX9675 EV kit software by opening its
18) Check the Output Enable checkbox in the
19) Press the Program button.
20) On the video measurement equipment, verify that
Wizard to install the USB device driver. Choose the
Search for the best driver for your device option.
Specify the location of the device driver to be
C:\Program Files\MAX9675 (default installation
directory) using the Browse button. During device
driver installation, Windows may show a warning
message indicating that the device driver Maxim
uses does not contain a digital signature. This is not
an error condition and it is safe to proceed with
installation. Refer to the USB_Driver_Help.PDF doc-
ument included with the software for additional
information.
icon in the Start | Programs menu. The EV kit soft-
ware main window appears, as shown in Figure 1.
Individual Output Setting group box.
the output signal matches the input signal.
DESCRIPTION
3