ISL54059EVAL1Z Intersil, ISL54059EVAL1Z Datasheet
ISL54059EVAL1Z
Specifications of ISL54059EVAL1Z
Related parts for ISL54059EVAL1Z
ISL54059EVAL1Z Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2008, 2009, 2011. All Rights Reserved Intersil (and design trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ...
Page 2
... These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. ...
Page 3
... Ld µTQFN Package (Note Maximum Junction Temperature (Plastic Package +150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C Pb-Free Reflow Profile .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C Power Supply Range . . . . . . . . . . . . . . . . . . . . . . . . +1.8V to +6.5V Test Conditions +4.5V to +5.5V, GND = 0V, V Otherwise Specified ...
Page 4
Electrical Specifications - 5V Supply PARAMETER NCx OFF Capacitance 1MHz (see Figure 7) C OFF COMx ON Capacitance 1MHz (see Figure 7) C COM(ON) POWER SUPPLY CHARACTERISTICS Positive Supply Current ...
Page 5
Electrical Specifications - 4.3V Supply PARAMETER COMx ON Capacitance 1MHz (see Figure 7) C COM(ON) POWER SUPPLY CHARACTERISTICS Positive Supply Current +4.5V, V Positive Supply Current +4.2V, V DIGITAL INPUT CHARACTERISTICS Input ...
Page 6
Electrical Specifications - 1.8V Supply PARAMETER ANALOG SWITCH CHARACTERISTICS ON-Resistance 1.8V V+, (see Figure 5) r Matching Between V+ = 1.8V Channels, Δr max Flatness ...
Page 7
Test Circuits and Waveforms V+ LOGIC 50% INPUT 0V t OFF SWITCH V NO INPUT V 90% SWITCH OUTPUT Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1A. MEASUREMENT POINTS SWITCH ...
Page 8
Test Circuits and Waveforms *50Ω SOURCE SIGNAL GENERATOR COM ANALYZER GND R L Signal direction through switch is reversed, worst case values are recorded. Repeat test for all switches. FIGURE 4. OFF-ISOLATION TEST CIRCUIT *50Ω SOURCE SIGNAL ...
Page 9
This method is not acceptable for the signal path inputs. Adding a series resistor to the switch input defeats the purpose of using a low r switch. Connecting external ON ...
Page 10
Typical Performance Curves 2 100mA V+ = 1.8V 1.8 COM 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0 (V) COM FIGURE 9. ON-RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE 1.00 ...
Page 11
Typical Performance Curves 700 650 600 ABSOLUTE VALUES ABSOLUTE VALUES 550 500 450 400 350 V+ = 3.3V 300 250 200 150 100 (V) COM FIGURE 15. ...
Page 12
Typical Performance Curves 0.05 707mV RMS 0.04 360mV RMS 0.03 177mV 0.02 RMS V+ = 3.3V 0. 0VDC BIAS R = 32Ω 100 200 1k FREQUENCY (Hz) FIGURE 21. TOTAL HARMONIC DISTORTION vs FREQUENCY 12 ...
Page 13
... Dimensions D2 and E2 are for the exposed pads which provide M 0. improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Compliant to JEDEC MO-229-WEED-3 except for D2 dimensions TERMINAL TIP MILLIMETERS MIN ...
Page 14
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...