V2DIP1-64 FTDI, Future Technology Devices International Ltd, V2DIP1-64 Datasheet - Page 8

• Manufacturer Part Number: V2DIP1-64
• Description: MOD MCU-USB HOST CTLR 60-DIP
• Manufacturer: FTDI, Future Technology Devices International Ltd
• Series: Vinculum-IIr

Specifications of V2DIP1-64

• Main Purpose: Interface, USB 2.0 Host/Controller
• Embedded: Yes, ASIC
• Utilized Ic / Part: VNC2-64Q
• Primary Attributes: Single A-Type Connector, UART / Parallel FIFO / SPI Interfaces
• Secondary Attributes: Second USB Port is Available via Pins, Traffic LEDs
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 768-1056

Table 3.1 - Pin Signal Descriptions
J2-8
J2-9
J2-10
J2-11
J2-12
J2-13
J2-14
J2-15
J2-16
J2-17
J2-18
J2-19
J2-20
J2-21
J2-22
J2-23
J2-24
J2-25
J2-26
J2-27
J2-28
J2-29
J2-30
Pin No.
IOBUS36
IOBUS35
IOBUS25
IOBUS24
IOBUS23
IOBUS22
IOBUS21
IOBUS20
IOBUS19
IOBUS18
RESET#
IOBUS4
IOBUS3
IOBUS2
IOBUS1
IOBUS0
Name
PROG#
GND
GND
3V3
3V3
3V3
-
on PCB
Copyright © 2010 Future Technology Devices International Limited
Name
PRG#
RST#
IO36
IO35
IO25
IO24
IO23
IO22
IO21
IO20
IO19
IO18
Pin
GND
GND
3V3
3V3
IO4
IO3
IO2
IO1
IO0
3V3
-
V2DIP1’s on board
V2DIP1’s on board
3.3V Output from
3.3V Output from
3.3V Output from
VDIP1’s on board
3.3V L.D.O.
3.3V L.D.O.
3.3V L.D.O.
V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01
Type
Input
Input
PWR
PWR
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
-
3.3V output from V2DIP1’s on board 3.3V L.D.O.
3.3V output from V2DIP1’s on board 3.3V L.D.O.
3.3V output from V2DIP1’s on board 3.3V L.D.O.
This pin is used in combination with the RESET#
pin and the UART interface to program firmware
into the VNC2.
5V safe bidirectional data / control bus bit 33
5V safe bidirectional data / control bus bit 34
Module ground supply pin
Not connected
5V safe bidirectional data / control bus bit 4
5V safe bidirectional data / control bus bit 3
5V safe bidirectional data / control bus bit 2
5V safe bidirectional data / control bus bit 1
5V safe bidirectional data / control bus bit 0
Can be used by an external device to reset the
VNC2. This pin is also used in combination with
PROG# and the UART interface to program
firmware into the VNC2
5V safe bidirectional data / control bus bit 25
5V safe bidirectional data / control bus bit 24
5V safe bidirectional data / control bus bit 23
Module ground supply pin
5V safe bidirectional data / control bus bit 22
5V safe bidirectional data / control bus bit 21
5V safe bidirectional data / control bus bit 20
5V safe bidirectional data / control bus bit 19
5V safe bidirectional data / control bus bit 18
Document Reference No.: FT_000165
Description
Clearance No.: FTDI# 154
7