KSZ8851-16MLL-EVAL Micrel Inc, KSZ8851-16MLL-EVAL Datasheet - Page 26
![BOARD EVALUATION KSZ8851-16MLL](/photos/9/6/90629/ksz8851-16mll-eval_sml.jpg)
KSZ8851-16MLL-EVAL
Manufacturer Part Number
KSZ8851-16MLL-EVAL
Description
BOARD EVALUATION KSZ8851-16MLL
Manufacturer
Micrel Inc
Series
LinkMD®r
Specifications of KSZ8851-16MLL-EVAL
Main Purpose
Interface, Ethernet Controller (PHY and MAC)
Embedded
No
Utilized Ic / Part
KSZ8851-16MLL
Primary Attributes
1 Port, 100BASE-TX/10BASE-T
Secondary Attributes
8/16-Bit Interface, LinkMD Cable Diagnostics
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
576-3292
Frame Transmitting Path Operation in TXQ
This section describes the typical register settings for transmitting packets from host processor to KSZ8851-16MLL with
generic bus interface. User can use the default value for most of the transmit registers. The following Table 8 describes all
registers which need to be set and used for transmitting single or multiple frames.
Driver Routine for Transmit Packet from Host Processor to KSZ8851-16MLL
The transmit routine is called by the upper layer to transmit a contiguous block of data through the Ethernet controller. It is
user’s choice to decide how the transmit routine is implemented. If the Ethernet controller encounters an error while
transmitting the frame, it’s the user’s choice to decide whether the driver should attempt to retransmit the same frame or
discard the data. The following Figures 7 and 8 shows the step-by-step for single and multiple transmit packets from host
processor to KSZ8851-16MLL.
August 2009
Micrel, Inc.
Register Name
[bit](offset)
TXCR[3:0](0x70)
TXCR[8:5](0x70)
TXMIR[12:0](0x78)
TXQCR[0](0x80)
TXQCR[1](0x80)
TXQCR[2](0x80)
RXQCR[3](0x82)
TXFDPR[14](0x84)
IER[14][6](0x90)
ISR[15:0](0x92)
TXNTFSR[15:0](0x9E)
Set transmit control function as below:
Set bit 3 to enable transmitting flow control. Set bit 2 to enable transmitting padding.
Set bit 1 to enable transmitting CRC. Set bit 0 to enable transmitting block operation.
Set transmit checksum generation for ICMP, UDP, TCP and IP packet.
The amount of free transmit memory available is represented in units of byte. The TXQ memory (6
KByte) is used for both frame payload and control word.
For single frame to transmit, set this bit 0 = 1(manual enqueue). the KSZ8851-16MLL will enable current
TX frame prepared in the TX buffer is queued for transmit, this is only transmit one frame at a time.
Note: This bit is self-clearing after the frame is finished transmitting. The software should wait for the bit
to be cleared before setting up another new TX frame.
When this bit is written as 1, the KSZ8851-16MLL will generate interrupt (bit 6 in ISR register) to CPU
when TXQ memory is available based upon the total amount of TXQ space requested by CPU at
TXNTFSR (0x9E) register.
Note: This bit is self-clearing after the frame is finished transmitting. The software should wait for the bit
to be cleared before set to 1 again
For multiple frames to transmit, set this bit 2 = 1 (auto-enqueue). the KSZ8851-16MLL will enable
current all TX frames prepared in the TX buffer are queued to transmit automatically.
Set bit 3 to start DMA access from host CPU either read (receive frame data) or write (transmit data
frame)
Set bit 14 to enable TXQ transmit frame data pointer register increments automatically on accesses to
the data register.
Set bit 14 to enable transmit interrupt in Interrupt Enable Register
Set bit 6 to enable transmit space available interrupt in Interrupt Enable Register.
Write 1 (0xFFFF) to clear all interrupt status bits after interrupt occurred in Interrupt Status Register.
The host CPU is used to program the total amount of TXQ buffer space which is required for next total
transmit frames size in double-word count.
Table 8. Registers Setting for Transmit Function Block
26
Description
KSZ8851-16MLL/MLLI
M9999-083109-2.0