EVL6563H-100W STMicroelectronics, EVL6563H-100W Datasheet - Page 30

• Manufacturer Part Number: EVL6563H-100W
• Description: EVAL BOARD FOR L6563 (100W)
• Manufacturer: STMicroelectronics
• Type: Power Factor Correctionr

Specifications of EVL6563H-100W

• Main Purpose: Power Management, Power Factor Correction
• Embedded: No
• Utilized Ic / Part: L6563
• Primary Attributes: 100W Power Factor Correction and Preregulator Combination
• Secondary Attributes: Transition Mode & Active Tracking Boost Function.
• Product: Power Management Modules
• Supply Current: 5 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: L6563H
• Other names: 497-10379; 497-10379-NHD

Application information
30/49
V(TBO)/RT, that is internally 1:1 mirrored and sunk from pin INV (#1) input of the L6563H's
error amplifier. In this way, when the mains voltage increases the voltage at TBO pin
increases as well and so does the current flowing through the resistor connected between
TBO and GND. Then a larger current is sunk by INV pin and the output voltage of the PFC
pre-regulator is forced to get higher. Obviously, the output voltage moves in the opposite
direction if the input voltage decreases.
To avoid undesired output voltage rise should the mains voltage exceed the maximum
specified value, the voltage at the TBO pin is clamped at 3V. By properly selecting the
multiplier bias it is possible to set the maximum input voltage above which input-to-output
tracking ends and the output voltage becomes constant. If this function is not used, leave
the pin open: the device regulates a fixed output voltage.
Starting from the following data:
●
●
●
●
●
to set the output voltage at the desired values use the following design procedure:
1.
2.
3.
4.
5.
Figure 43
Vin
Vin
Vo
Vo
Vox = absolute maximum limit for the regulated output voltage;
Determine the input RMS voltage Vinclamp that produces Vo = Vox:
and choose a value Vin
the output voltage range below Vox (it is equal Vox if one chooses Vin
Determine the divider ratio of the MULT pin (#3) bias:
and check that at minimum mains voltage Vin1 the peak voltage on pin 3 is greater than
0.65 V.
Determine R1, the upper resistor of the output divider, for instance 3 MΩ.
Calculate the lower resistor R2 of the output divider and the adjustment resistor RT:
Check that the maximum current sourced by the TBO pin (#6) does not exceed the
maximum specified (0.2 mA):
1
2
1
2
= regulated output voltage @ Vin = Vin
= regulated output voltage @ Vin = Vin
= minimum specified input RMS voltage;
= maximum specified input RMS voltage;
shows the internal block diagram of the tracking boost function.
⎧
⎪ ⎪
⎨
⎪
⎪
⎩
R
R
Vin
2
T
=
=
clamp
2
x
5 .
2
such that Vin
Doc ID 16047 Rev 3
⋅
⋅
=
R
k
1
⋅
I
Vox
Vo
TBO
R
⋅
(
1
Vo
2
⋅
max
Vin
−
−
Vo
1
k
Vo
Vo
−
=
2
2
=
2
2
1
1
−
−
5 .
R
≤
3
⋅
2
Vin
Vo
T
)
Vin
Vinx < Vinclamp. This results in a limitation of
⋅
⋅
3
Vin
≤
Vin
Vin
1
1
2
1
2
;
;
0
2 .
−
2
x
2
−
Vox
−
Vo
⋅
10
(
Vin
Vo
2
−
−
3
−
1
2
Vo
Vo
−
2
2
1
5 .
⋅
)
Vin
⋅
Vin
1
1
x
= Vin
clamp
L6563H
)