LPS110 Series
Notes (refer to table)
1. Peak current lasting < 30 seconds with a maximum 10% duty cycle.
2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a 0.1 µF capacitor.
4. Total power drawn must not exceed 80W with convection cooling or 110W fan cooled.
Input Specifications
Input range
Frequency
Inrush current
Input current
Efficiency
EMI filter
Electromagnetic
compatibility
Safety ground
leakage current
Environmental
Mating Connectors
AC Input:
DC Output:
Contacts:
Sense / P OK: Housing Molex 22-01-2025
Contacts:
Operating temperature: 0°C to 50°C ambient;
Storage temperature:-40°C to 85°C
Thermal regulation: ± 0.04% / °C
MTBF:
Notes
1 Specifications subject to change without notice.
2 All dimensions are in mm and (inches).
3 Mounting holes M1 and M2 should be earthed for EMI purposes.
4 Output Common capacitivily coupled to M2 earth.
5 Mounting hole M1 is safety earth connection. This power supply
6 Weight 0.75 kg / 1.65 lb.
Installation Notes
derate at 2.5% / °C from 50°C to 70°C
ambient conditions
must be earthed for safe operation via mounting hole M1 or SK1-3
connector.
Warning: Hazardous mains voltages present within
this unit. Primary heatsink is live. Please see enclosed
‘Astec Installation and Operating Instructions’. Use of
optional cover kit is recommended for safe operation.
> 100,000 hours at full load and 25°C
18/24 AWG Molex 08-50-0106
22/30 AWG Molex 08-50-0114
Housing Molex 09-91-0500
Housing Molex 09-91-0900
85 VAC to 264 VAC
120 to 370 VDC
47 - 440 Hz
< 18 A peak @ 115 VAC
< 36 A peak @ 230 VAC
2.5 A max. (RMS) @ 115 VAC
70% typical at full load
Meets FCC Class B
CISPR 22 Class B
(includes EN55022 class B and
VDE 0878 PT3 class B)
Meets IEC801-2 level 3,
< 0.5mA @ 50/60Hz,
and IEC801-5 level 3
264Vac input
IEC801-4 level 3
110 Watts
(or 26-03-4050)
(or 26-03-4090)
(or 08-58-0189)
Single Output
Output Specifications
Maximum
total wattage
Adjustment
range
Hold-up time
Overload
protection
Overvoltage
protection
Safety
VDE
UL
CSA
NEMKO
BABT
CB
This product is CE marked following
the provisions of the Low Voltage
Directive 73/23/EEC
0805/EN60950 (IEC950)
UL1950
CSA 22-2-234 Level 3
EN 60950/EMKO-TUE (74-sec) 203
EN60950/BS7002
Certificate and report
Cover available
Overall dimensions with cover -
193.5 (7.62) x 115.6 (4.55) x 63 (2.48).
Total power with cover derates to:- 70W
convection, 90W with 30CFM forced air.
Input fuse 4A 20mm Quick Acting HBC
mains fuse - only replace with same type
and rating to maintain safety standards.
Power OK
SK202
Power OK signal;-TTL compatible signal
goes high 50-150ms after switch on. Goes
low >1.5 ms before loss of regulation
Remote Sense
SK201
This power supply has a connector for output
remote sense. This can be used to
compensate for cable voltage drops of up to
0.5V. If this feature is not used the power
supply reverts to internal local sense.
Protected against reverse connection.
Cover
Fusing
80 W for convection;
110 W with 30 CFM forced air
± 5% minimum
20 ms at full load and 115 VAC
nominal line
Short circuit protection on all outputs.
Auto recovery. Total power limited @
110% to 135% above peak rating
5V output: 5.7 to 6.7 Vdc. Other
outputs 10 to 25% above nominal
output; recycle AC to reset
pin2 common
pin2 -sense
pin1 POK
pin1 +sense
1
2
1
2