ZUP6-33/U TDK Corporation, ZUP6-33/U Datasheet - Page 43

• Manufacturer Part Number: ZUP6-33/U
• Description: PWR SUP BENCH PROG 0-6V 198W
• Manufacturer: TDK Corporation
• Series: ZUPr
• Type: Programmabler

Specifications of ZUP6-33/U

• Voltage - Output: 0 ~ 6V
• Number Of Outputs: 1
• Power (watts): 198W
• Applications: Commercial
• Power Supply Type: Switching (Closed Frame)
• Voltage - Input: 85 ~ 265VAC
• Mounting Type: Chassis Mount
• 1st Output: 0 ~ 6 VDC @ 33A
• Size / Dimension: 13.78" L x 4.88" W x 2.76" H (350mm x 124mm x 70mm)
• Power (watts) - Rated: 198W
• Operating Temperature: 0°C ~ 50°C
• Efficiency: 72%
• Approvals: CE, EN, UL
• Line Regulation: 0.01%
• Load Regulation: 0.01%
• Accuracy: 0.02% + 5 mV
• Brand/series: ZUP
• Current, Output: 33 A
• Display Type: Digital Meter
• Power, Output: 198 W
• Power, Rating: 198 W (Max.)
• Regulation, Line: 0.01% + 2 mA⁄1 mV + 0.005%
• Regulation, Load: 0.01% + 5 mA⁄2 mV + 0.005%
• Standards: UL Listed, CE Marked
• Temperature Coefficient: 30 ppm⁄°C (CV)⁄100 ppm⁄°C (CC)
• Temperature, Operating, Maximum: 50 °C
• Temperature, Operating, Minimum: 0 °C
• Voltage, Input: 85-265 VAC
• Voltage, Noise: 50 mV @ 20 MHz BW
• Voltage, Output: 6 VDC
• Voltage, Ripple: 5 mV @ 5 Hz to 1 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 285-1683; ZUP633/U

4.4.15 Output Good Signal
Output Good Signal is an open collector output, referenced to COM potential, indicating the status of
the power supply output. While the power supply operates normally, the Output Good is low (0~0.8V).
When the power supply output is disabled due to activated OVP, OTP or FOLD protection, or by OUT
set to off, or by ac ON/OFF set to off, then the output signal stops conducting. The maximum sink
current is 10mA and the maximum voltage is 40VDC.
Typical applications of Output Good Signal
1. In multiple power supply systems, it is possible to disable all the units when a critical unit fails. Refer
( )
Fig. 4-15: Disabling multiple supply systems.
2. Hierarchical structure in multiple supply systems:It is possible to define a hierarchy in multiple supply
*
Critical
ZUP
Unit # 1
to Fig 4-15 for typical connection diagram.
systems by enabling any N+1 unit by the Output Good signal of the N unit. In this structure, failure of
the N unit will cause all the following units to be disabled. Refer to Fig 4-16 for typical connections
diagram.
The Output Good Signal is referenced to the COM potential, therefore pay attention NOT to
For models with output voltage rating greater than 40V use
a Zener diode to limit the Output Good voltage below 40V.
The resistor and Zener power rating must be greater than the
maximum actual power dissipation.
OUT.GOOD
ZUP # 2
ZUP # 1
+V
- V
short it to another potential as it may damage the unit.
PCn
COM
- V
OUT.GOOD
OUT.GOOD
I = 5mA
ON/OFF
ON/OFF
COM
COM
- V
+V
+V
PC1
( )
*
CAUTION
( )
*
( )
PC1-A
PC2-A
PC1-B
*
ZUP #
ZUP #
ZUP #
Fig. 4-16: Hierarchical structure in
OUT.GOOD
n
ON/OFF
n
n
COM
ON/OFF
ON/OFF
+V
multiple supply systems.
COM
COM
+V
- V
+V
- V
PCn
PC( -1)-B
PC1
n