AM80A-048L-050P25D033P30 Emerson Network Power, AM80A-048L-050P25D033P30 Datasheet - Page 6

• Manufacturer Part Number: AM80A-048L-050P25D033P30
• Description: CONV DC-DC 240W 48VIN 3.3/5V DL
• Manufacturer: Emerson Network Power
• Series: AM80Ar
• Type: Point of Load (POL) Non-Isolatedr

Specifications of AM80A-048L-050P25D033P30

• Output: 5V, 3.3V
• Number Of Outputs: 2
• Power (watts): 240W
• Mounting Type: Through Hole
• Voltage - Input: 36 ~ 72V
• Package / Case: Module
• 1st Output: 5 VDC @ 25A
• 2nd Output: 3.3 VDC @ 30A
• Size / Dimension: 4.60" L x 2.40" W x 0.50" H (116.8mm x 61mm x 12.7mm)
• Power (watts) - Rated: 240W
• Operating Temperature: -20°C ~ 100°C
• Approvals: CE, CSA, EN, UL, VDE
• 3rd Output: -
• Other names: 454-1106

6
Electrical Specifications
Absolute Maximum Ratings – all models
Exceeding the specified absolute maximum ratings may severely damage the module. These ratings are intended as
guidelines for absolute worst case operating conditions and are not to be interpreted as recommended operating
condition
Specifications
Electrical characteristics are guaranteed over the full baseplate/ case temperature range (-20 to 100°C*) and for the full
range of input voltage (V
connected to the output terminals at the point of measurement, ENABLE is connected to -SENSE. All other pins are left
floating.
Definitions
V
*Note : AM80A-048L-050P25D033P30 Baseplate/ Case Operating Temperature is -20 to 85°C.
Secondary Control Pins
+SENSE
-SENSE
TEM P MON
C MON
C SHA RE
CLK OUT
CLK IN
C LIM ADJ
OVP A DJ
V ADJ
PG/ID
ENA BLE
Note : V
General
Continuous Input Voltage
Input Surge Voltage (1 sec)
Isolation, Input to Output*
Isolation Input to Baseplate*
Isolation, Output to Bas eplate*
Operating Temperature (Baseplate) /Cas e
Storage Temperature
Operating Relative Humidity (non-condensing)
Storage Relative Humidity (non-condensing)
A ltitude (Operating)
A ltitude (Storage)
Lead Temperature (soldering 5 Seconds)
I
, V
AMPSS
O
All voltage referenced to negative output
and I
o
= module output voltage
O
are actual operating conditions, V
®
Reference Manual
V
-0.5 to 0.5 VDC
-0.5 to 7 VDC
-0.5 to 7 VDC
-0.5 to 7 VDC
-50 to 50 VDC
-50 to 50 VDC
-0.5 to 7 VDC
-0.5 to 7 VDC
-0.5 to 7 VDC
0.5 to V
-0.5 to 20 VDC
o
I
- 0.5 to V
) and for the full load range (0 to I
o
+ 0.5VDC
o
+ 0.5 VDC
Inom
, V
320V Input
2700VDC
2121VDC
Onom
500VDC
400V
425V
and I
O
rated). Except where indicated , +SENSE and -SENSE are
Notes:
* For 300/320V input :
All isolation barriers on 300V input modules have been designed
and tested to meet 4242VDC as required by IEC950 for reinforced
insulation. The complete module should NOT be subjected to a
3000VAC input-to-output test because this can result in input-
baseplate-output breakdown. AMPSS DC-DC modules are CLASS
I equipment. Power supply systems using AMPSS modules MUST
also be CLASS I equipment. Each AMPSS DC-DC module is fully
tested in factory according to the standards. Therefore power
supply systems need only be subjected to Hi-Pot test for BASIC
insulation which is 1500Vac (AC) input to GROUND.
Orated
300V Input
400V
425V
2700VDC
2121VDC
500VDC
are nominal ratings.
-20 to 100°C *
-40 to 105°C
10% to 95%
95% M ax
< 3000m
< 9000m
235°C
150V Input
2700VDC
200V
225V
2121VDC
500VDC
48V Input
72V
75V (continuous)
2100VDC
2100VDC
500VDC
Rev. 05 Mar 99