PTH03010WAD Emerson Network Power, PTH03010WAD Datasheet - Page 2

• Manufacturer Part Number: PTH03010WAD
• Description: CONV DC/DC 3.3VIN ADJOUT 15A
• Manufacturer: Emerson Network Power
• Series: PTH03010Wr
• Type: Point of Load (POL) Non-Isolatedr

Specifications of PTH03010WAD

• Output: 0.8 ~ 2.5V
• Number Of Outputs: 1
• Power (watts): 37W
• Mounting Type: Through Hole
• Voltage - Input: 2.95 ~ 3.65V
• Package / Case: 10-DIP Module
• 1st Output: 0.8 ~ 2.5 VDC @ 15A
• Size / Dimension: 1.37" L x 0.62" W x 0.35" H (34.8mm x 15.7mm x 8.9mm)
• Power (watts) - Rated: 37.5W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 93%
• Approvals: CSA, cUL, TUV, UL
• Output Power: 38 W
• Input Voltage Range: 2.95 V to 3.65 V
• Input Voltage (nominal): 3.3 V
• Output Voltage (channel 1): 0.8 V to 2.5 V
• Output Current (channel 1): 15 A
• Package / Case Size: 34.8 mm x 15.75 mm x 9 mm
• Output Voltage: 0.8 V to 2.5 V
• Product: Non-Isolated / POL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 393-1159

Part Number System with Options
N N o o t t e e s s
1
2
3
4
5
6
7
8
9
10
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
DC-DC CONVERTERS
OUTPUT
POWER
(MAX.)
37.5 W
Remote ON/OFF. Positive Logic
ON:
OFF:
See Figures 1 and 2 for safe operating curves.
A 470 µF electrolytic input capacitor is required for proper operation. The
capacitor must be rated for a minimum of 700 mA rms of ripple current.
An external output capacitor is not required for basic operation. Adding
330 µF of distributed capacitance at the load will improve the transient
response.
1 A/µs load step, 50 to 100% I
If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point).
The pre-bias start-up feature is not compatible with Auto-Track ™ . This is
because when the module is under Auto-Track ™ control, it is fully active
and will sink current if the output voltage is below that of a back-feeding
source. Therefore to ensure a pre-bias hold-off, one of the following two
techniques must be followed when input power is first applied to the
module. The Auto-Track ™ function must either be disabled, or the
module’s output held off using the Inhibit pin. Refer to Application Note
150 for more details.
Tape and reel packaging only available on the surface-mount versions.
To order Pb-free (RoHS compatible) surface-mount parts replace the
mounting option ‘S’ with ‘Z’, e.g. PTH03010WAZ. To order Pb-free
(RoHS compatible) through-hole parts replace the mounting option ‘H’
with ‘D’, e.g. PTH03010WAD.
NOTICE: Some models do not support all options. Please contact your
local Artesyn representative or use the on-line model number search tool at
http://www.artesyn.com/powergroup/products.htm to find a suitable
alternative.
Pin 3 open; or V > Vin - 0.5 V
Pin 3 GND; or V < 0.8 V (min - 0.2 V).
2.95-3.65 V
VOLTAGE
INPUT
Mechanical Package
Point of Load Alliance
POLA Non-isolated
omax
Product Family
Output Current
Input Voltage
, C
VOLTAGE
OUTPUT
0.8-2.5 V
3 . 3 V i n s i n g l e o u t p u t
Compatible
The ultra-wide output voltage trim range offers major advantages to users who
select the PTH03010. It is no longer necessary to purchase a variety of
modules in order to cover different output voltages. The output voltage can be
trimmed in a range of 0.8 Vdc to 2.5 Vdc. When the PTH03010 converter
leaves the factory the output has been adjusted to the default voltage of 0.8 V.
03 = 3.3 V
PTH03010
out
01 = 15 A
Always 0
= 330 µF.
O O u u t t p p u u t t V V o o l l t t a a g g e e A A d d j j u u s s t t m m e e n n t t o o f f t t h h e e P P T T H H 0 0 3 3 0 0 1 1 0 0 S S e e r r i i e e s s
CURRENT
OUTPUT
(MIN.)
P T H 0 3 0 1 0 W A S T
0 A
CURRENT
OUTPUT
(MAX.)
15 A
EFFICIENCY
(MAX.)
93%
OUTPUT VOLTAGE
EFFICIENCY TABLE (I
Vo = 1.0 V
Vo = 1.2 V
Vo = 1.5 V
Vo = 1.8 V
Vo = 2.0 V
Vo = 2.5 V
Packaging Options
No Suffix = Trays
T = Tape and Reel
Pin Option
A = Through-Hole Std. Pin Length (0.140”)
A = Surface-Mount Tin/Lead Solder Balll
Output Voltage Code
W = Wide
Mounting Option
D = Horizontal Through-Hole (Matte Sn)
H = Horizontal Through-Hole (Sn/Pb)
S = Surface-Mount (63/37 Sn/Pb
Z = Surface-Mount (96.5/3.0/0.5 Sn/Ag/Cu
±10 mV
LINE
pin solder material)
pin solder material)
REGULATION
File Name: pth03010.pdf Rev (06): 16 Dec 2005
±12 mV
LOAD
(9)
(8)
EFFICIENCY
O
NEW Product
= 10 A)
85%
87%
89%
91%
92%
93%
NUMBER
PTH03010
MODEL
(9,10)
2