LTM4602EV#PBF Linear Technology, LTM4602EV#PBF Datasheet - Page 6

• Manufacturer Part Number: LTM4602EV#PBF
• Description: IC DC/DC UMODULE 6A 104-LGA
• Manufacturer: Linear Technology
• Series: µModuler
• Type: Point of Load (POL) Non-Isolatedr

Specifications of LTM4602EV#PBF

• Design Resources: LTM4602 Spice Model
• Output: 0.6 ~ 5 V
• Number Of Outputs: 1
• Power (watts): 30W
• Mounting Type: Surface Mount
• Voltage - Input: 4.5 ~ 20V
• Package / Case: 104-LGA
• 1st Output: 0.6 ~ 5 VDC @ 6A
• Size / Dimension: 0.59" L x 0.59" W x 0.11" H (15mm x 15mm x 2.8mm)
• Power (watts) - Rated: 30W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 92%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -

PIN FUNCTIONS
LTM4602
V
tween these pins and PGND pins. Recommend placing
input decoupling capacitance directly between V
and PGND pins.
f
the one-shot timer current, thereby setting the switching
frequency. The LTM4602 switching frequency is typically
850kHz. An external resistor to ground can be selected to
reduce the one-shot timer current, thus lower the switching
frequency to accommodate a higher duty cycle step down
requirement. See the applications section.
SV
this pin open or add additional decoupling capacitance.
EXTV
left open or grounded, the internal 5V linear regulator will
power the controller and MOSFET drivers. For high input
voltage applications, connecting this pin to an external
5V will reduce the power loss in the power module. The
EXTV
V
Internally, this pin is connected to V
resistor. Different output voltages can be programmed with
additional resistors between the V
COMP (Pin B23): Current Control Threshold and Error
Amplifi er Compensation Point. The current comparator
threshold increases with this control voltage. The voltage
ranges from 0V to 2.4V with 0.8V corresponding to zero
sense voltage (zero current).
6
ADJ
OSET
IN
IN
(Bank 1): Power Input Pins. Apply input voltage be-
(Pin A15): A 110k resistor from V
(Pin A17): Supply Pin for Internal PWM Controller. Leave
CC
CC
(Pin A21): The Negative Input of The Error Amplifi er.
(Pin A19): External 5V supply pin for controller. If
voltage should never be higher than V
(See Package Description for Pin Assignment)
OUT
OSET
BANK 1
BANK 2
BANK 3
with a 100k precision
PGND
V
OUT
V
and SGND pins.
IN
IN
1 2
2 5
3 2
to this pin sets
1
8
1
3 9
5 0
6 1
7 2
8 3
9 4
2
3
2
8 4
9 5
4 0
5 1
6 2
7 3
4
IN
5
3
.
4 1
5 2
6 3
7 4
8 5
9 6
6
IN
2 6
3 3
7
4
4 2
5 3
6 4
7 5
8 6
9 7
8
pins
2 7
3 4
9
5
10
1 3
4 3
5 4
6 5
7 6
8 7
9 8
9
TOP VIEW
11
2 8
3 5
6
12
1 0
1 4
4 4
5 5
6 6
7 7
8 8
9 9
13
2 9
3 6
7
14
1 0 0
1 1
1 5
4 5
5 6
6 7
7 8
8 9
SGND (Pin D23): Signal Ground Pin. All small-signal
components should connect to this ground, which in turn
connects to PGND at one point.
RUN/SS (Pin F23): Run and Soft-Start Control. Forcing
this pin below 0.8V will shut down the power supply.
Inside the power module, there is a 1000pF capacitor
which provides approximately 0.7ms soft-start time with
200μF output capacitance. Additional soft-start time can
be achieved by adding additional capacitance between the
RUN/SS and SGND pins. The internal short-circuit latchoff
can be disabled by adding a resistor between this pin and
the V
5μA pull up current.
FCB (Pin G23): Forced Continuous Input. Grounding this
pin enables forced continuous mode operation regardless
of load conditions. Tying this pin above 0.63V enables
discontinuous conduction mode to achieve high effi ciency
operation at light loads. There is an internal 4.75k resistor
between the FCB and SGND pins.
PGOOD (Pin J23): Output Voltage Power Good Indicator.
When the output voltage is within 10% of the nominal
voltage, the PGOOD is open drain output. Otherwise, this
pin is pulled to ground.
PGND (Bank 2): Power ground pins for both input and
output returns.
V
between these pins and PGND pins. Recommend placing
High Frequency output decoupling capacitance directly
between these pins and PGND pins.
3 0
15
1 6
3 7
OUT
1 0 1
4 6
5 7
6 8
7 9
9 0
16
1 7
3 1
3 8
17
IN
1 0 2
18
4 7
5 8
6 9
8 0
9 1
(Bank 3): Power Output Pins. Apply output load
1 8
19
pin. This pullup resistor must supply a minimum
1 0 3
20
4 8
5 9
7 0
8 1
9 2
1 9
21
1 0 4
4 9
6 0
7 1
8 2
9 3
22
23
2 0
2 1
2 2
2 3
2 4
A
C
E
G
J
L
M
N
P
R
T
B
D
F
H
K
COMP
SGND
RUN/SS
FCB
PGOOD
4602 PN01
4602fa