LTW-150TK Lite-On Electronics, LTW-150TK Datasheet
LTW-150TK
Specifications of LTW-150TK
Available stocks
Related parts for LTW-150TK
LTW-150TK Summary of contents
Page 1
... Compatible with automatic placement equipment. * Compatible with infrared reflow solder process. * EIA STD package. * I.C. compatible. Package Dimensions Part No. LTW-150TK Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.10 mm (.004") unless otherwise noted. Part No. : LTW-150TK BNS-OD-C131/ Lens Emitted Color Yellow InGaN White Page : 1 of ...
Page 2
... Duty Cycle, 0.1ms Pulse Width) DC Forward Current Reverse Voltage Operating Temperature Range Storage Temperature Range Infrared soldering condition Note: Revered Voltage can’t be continued operation . Suggest IR Reflow Condition : Part No. : LTW-150TK BNS-OD-C131/ Ta=25℃ ℃ ℃ ℃ LTW-150TK 100 260°C For 10 Seconds Unit ...
Page 3
... LED. All devices, equipment and machinery must be properly grounded. 5. Tester PR704 is for the chromaticity coordinates (x, y). EG&G is for Iv 6. The chromaticity coordinates (x, y) guarantee should be added ± 0.01 tolerance. Part No. : LTW-150TK BNS-OD-C131/ Ta=25℃ ℃ ℃ ℃ Part No. ...
Page 4
... LITE-ON TECHNOLOGY CORPORATION Typical ℃ (25 Part No. : LTW-150TK BNS-OD-C131/ Electrical / Optical Characteristics Ambient Temperature Unless Curves Otherwise Noted) Page : ...
Page 5
... LITE-ON TECHNOLOGY CORPORATION Bin Code List VF Bin IV Bin Hue Bin K1 K2 Part No. : LTW-150TK BNS-OD-C131/ Spec. Table Forward Voltage Min. 2 2.80 3 3.00 4 3.20 5 3.40 6 3.60 Tolerance on each Forward Voltage bin is +/-0.1 volt IV Spec. Table Luminous Intensity (mcd 20mA Min. R 112.0 S 180.0 T 280.0 Tolerance on each Luminous Intensity bin is +/- 15% ...
Page 6
... Do not use unspecified chemical liquid to clean LED they could harm the package. If clean is necessary, immerse the LED in ethyl alcohol or in isopropyl alcohol at normal temperature for less one minute. Suggest Soldering Pad Dimensions Package Dimensions Of Tape And Reel Notes: 1. All dimensions are in millimeters (inches). Part No. : LTW-150TK BNS-OD-C131/ Page : ...
Page 7
... LITE-ON TECHNOLOGY CORPORATION Package Dimensions of Reel Notes: 1. Empty component pockets sealed with top cover tape inch reel-3000 pieces per reel. 3. Minimum packing quantity is 500 pcs for remainders. 4. The maximum number of consecutive missing lamps is two accordance with ANSI/EIA 481-1-A-1994 specifications. Part No. : LTW-150TK BNS-OD-C131/ Page : ...
Page 8
... LITE-ON TECHNOLOGY CORPORATION Notes: 1. There are 3 moisture barrier bags or less in inner carton. 2. There are 21 inner carton or less in a master carton. Part No. : LTW-150TK BNS-OD-C131/ Page : ...
Page 9
... You can use this example as a generic target to set up your reflow process. You should adhere to the JEDEC profile limits as well as specifications and recommendations from the solder paste manufacturer to avoid damaging the device and create a reliable solder joint. Part No. : LTW-150TK BNS-OD-C131/ CAUTIONS 150~200° ...
Page 10
... To verify for ESD damage, check for “ lightup ” and Vf of the suspect LEDs at low currents. The Vf of “ good ” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. Part No. : LTW-150TK BNS-OD-C131/ Circuit model B ...
Page 11
... Resistance Environmental Test IR-Reflow Solderability 8. Others The appearance and specifications of the product may be modified for improvement without prior notice. Part No. : LTW-150TK BNS-OD-C131/ Test Condition Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 500HRS (-24HRS,+72HRS)*@20mA. Ta= 65±5℃,RH= 90～95% *Test Time= 240HRS± ...
Page 12
... No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycles? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTW-150TK BNS-OD-C131/ Page : 12 of ...