FTLF1424P2BCD Finisar Corporation, FTLF1424P2BCD Datasheet - Page 6

• Manufacturer Part Number: FTLF1424P2BCD
• Description: TXRX OPT SFP 4 GB/S 1310NM
• Manufacturer: Finisar Corporation

Specifications of FTLF1424P2BCD

• Data Rate: 4.25Gbps
• Wavelength: 1310nm
• Applications: Ethernet
• Voltage - Supply: 3 V ~ 3.6 V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Standard Supported: 1000BASE-LX|IEEE 802.3
• Number Of Transceivers: 1
• Minimum Single Supply Voltage: 3 V
• Maximum Single Supply Voltage: 3.6 V
• Operating Supply Voltage: 3.3 V
• Maximum Supply Current: 300 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 775-1025

F i n i s a r
FTLF1424P2xCR and FTLF1424P2xCD SFP Product Specification – April 2007
VIII. Digital Diagnostic Functions
Finisar FTLF1424P2xCR and FTLF1424P2xCD SFP transceivers support the 2-wire
1
serial communication protocol as defined in the SFP MSA
. It is very closely related to
2
the E
PROM defined in the GBIC standard, with the same electrical specifications.
The standard SFP serial ID provides access to identification information that describes
the transceiver’s capabilities, standard interfaces, manufacturer, and other information.
Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic
monitoring interface, which allows real-time access to device operating parameters such
as transceiver temperature, laser bias current, transmitted optical power, received optical
power and transceiver supply voltage. It also defines a sophisticated system of alarm and
warning flags, which alerts end-users when particular operating parameters are outside of
a factory set normal range.
2
The SFP MSA defines a 256-byte memory map in E
PROM that is accessible over a
2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic
monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally
defined serial ID memory map remains unchanged. The interface is identical to, and is
thus fully backward compatible with both the GBIC Specification and the SFP Multi
Source Agreement. The complete interface is described in Finisar Application Note AN-
2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed
through a 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the
2
SFP transceiver into those segments of the E
PROM that are not write-protected. The
negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod
Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with
SCL to mark the start and end of serial protocol activation. The memories are organized
as a series of 8-bit data words that can be addressed individually or sequentially.
1,5
For more information, please see the SFP MSA documentation
or Finisar Application
Note AN-2030.
FTLF1424P2xCR and FTLF1424P2xCD transceivers can be used in host systems that
require either internally or externally calibrated digital diagnostics.
Please note that evaluation board FDB-1018 is available with Finisar ModDEMO
software that allows simple to use communication over the 2-wire serial interface.
© Finisar Corporation April 5, 2007 Rev F1
Page 6