FTLF1424P2BCD Finisar Corporation, FTLF1424P2BCD Datasheet - Page 5

• Manufacturer Part Number: FTLF1424P2BCD
• Description: TXRX OPT SFP 4 GB/S 1310NM
• Manufacturer: Finisar Corporation

Specifications of FTLF1424P2BCD

• Data Rate: 4.25Gbps
• Wavelength: 1310nm
• Applications: Ethernet
• Voltage - Supply: 3 V ~ 3.6 V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Standard Supported: 1000BASE-LX|IEEE 802.3
• Number Of Transceivers: 1
• Minimum Single Supply Voltage: 3 V
• Maximum Single Supply Voltage: 3.6 V
• Operating Supply Voltage: 3.3 V
• Maximum Supply Current: 300 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 775-1025

FTLF1424P2xCR and FTLF1424P2xCD SFP Product Specification – April 2007
10. Measured with conformance signals defined in FC-PI-2 Rev. 10.0 specifications. Value in OMA.
11. Measured with conformance signals defined in FC-PI-2 Rev. 10.0 specifications. Represents
12. Rate Selectable version in low bandwidth mode with minimum 9dB extinction ratio.
13. Rate Selectable version in low bandwidth mode.
14. Rate Selectable version in high bandwidth mode.
V.
Data Rate
Bit Error Rate
Max. Supported Link Length on
9/125 μm SMF @ 4X Fibre Channel
Max. Supported Link Length on
9/125μm SMF @ 1X and 2X Fibre
Channel
Max. Supported Link Length on
9/125μm SMF @ Gigabit Ethernet
Notes:
1. Gigabit Ethernet and 1x/2x/4x Fibre Channel compliant.
2. Tested with a PRBS 2
3.
4.
VI.
These Finisar 1310nm Commercial Temperature SFP transceivers have an operating
temperature range from –10°C to +70°C case temperature.
Case Operating Temperature
Storage Temperature
VII.
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations.
These products are certified by TÜV and CSA to meet the Class 1 eye safety
requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC)
60950. Copies of certificates are available at Finisar Corporation upon request.
© Finisar Corporation April 5, 2007 Rev F1
Measured with PRBS 2
sensitivity based on OMA spec, as corrected to incoming Extinction Ratio of 13 dB (for example, at
5.75dB incoming extinction ratio, an OMA of 0.029 mW corresponds to -16 dBm sensitivity).
Measured with PRBS 2
Distances are based on FC-PI-2 Rev. 10.0 and IEEE 802.3 standards.
Distances are indicative only. Please refer to the Optical Specifications in Section IV to calculate a
more accurate link budget based on specific conditions in your application.
General Specifications
Environmental Specifications
Regulatory Compliance
Parameter
Parameter
7
-1 test pattern.
7
7
-1 at 10
-1 at 10
-12
-12
BER
BER .
Symbol
Symbol
L
L
L
BER
T
BR
T
MAX1
MAX2
MAX3
sto
op
Page 5
1062
Min
Min
-10
-40
Typ
Typ
10
20
20
Max
4250
Max
10
70
85
-12
F i n i s a r
Mb/sec 1
Units
Units
km
km
km
°C
°C
2
3
3,4
3,4
Ref.
Ref.