AFBR-5903AZ Avago Technologies US Inc., AFBR-5903AZ Datasheet - Page 16

• Manufacturer Part Number: AFBR-5903AZ
• Description: TXRX OPT FE MTRJ EXT TEMP 2X5DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of AFBR-5903AZ

• Data Rate: 100Mbps
• Wavelength: 1300nm
• Applications: General Purpose
• Voltage - Supply: 3.3V
• Connector Type: MTRJ
• Mounting Type: Through Hole
• Function: Implement FDDI and ATM at the 100 Mbps/125 MBd rate
• Product: Transceiver
• Maximum Rise Time: 3 ns/2.2 ns
• Maximum Fall Time: 3 ns/2.2 ns
• Pulse Width Distortion: 0.12 ns/0.2 ns
• Maximum Output Current: 50 mA
• Operating Supply Voltage: 3.135 V to 3.465 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package / Case: DIP With Connector
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Multimode Glass
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1992

For product information and a complete list of distributors, please go to our web site:
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries.
Data subject to change. Copyright © 2006 Avago Technologies Limited. All rights reserved. Obsoletes 5989-3084EN
AV02-0031EN - July 5, 2007
21. This value is measured during the transition from low to high levels
22. The Signal Detect output shall be asserted within 100 µs after a
23. This value is measured during the transition from high to low levels
24. Signal detect output shall be de-asserted within 350 µs af-
of i nput o ptical p ower. A t S ignal D etect D eassert, t he r eceiver o utputs
Data Out and Data Out Bar go to steady PECL levels High and Low
respectively.
step increase of the Input Optical Power. The step will be from a
low Input Optical Power, -45 dBm, into the range between greater
than P
or better during the time, LS_Max (15 µs) after Signal Detect has
been asserted. See Figure 14 for more information.
of i nput o ptical p ower. T he m aximum v alue w ill o ccur w hen t he i nput
optical power is either -45 dBm average or when the input optical
power yields a BER of 10
ter a step decrease in the Input Optical Power from a level
which is the lower of; -31 dBm or P
level at which signal detect was deasserted), to a power level of
-45 dBm or less. This step decrease will have occurred in less than
8 ns. The receiver output will have a BER of 10
period of 12 µs or until signal detect is deasserted. The input data
stream is the Quiet Line State. Also, signal detect will be deasserted
within a maximum of 350 µs after the BER of the receiver output
degrades above 10
with a negative ramp function instead of a step function. See Figure
14 for more information. At Signal Detect Deassert, the receiver
outputs Data Out and Data Out Bar go to steady PECL levels High
and Low respectively.
A
, and -14 dBm. The BER of the receiver output will be 10
-2
for an input optical data stream that decays
-2
or larger, whichever power is higher.
D
+ 4 dB (P
-2
or better for a
D
is the power
-2
www.avagotech.com